SAM
https://sam.ensam.eu:443
The DSpace digital repository system captures, stores, indexes, preserves, and distributes digital research material.Mon, 15 Apr 2024 16:44:30 GMT2024-04-15T16:44:30ZNumerical investigation of the real and ideal gap profiles in the calculation of the pressure distortion coefficient and piston fall rate of an LNE 200 MPa pressure balance
http://hdl.handle.net/10985/8914
Numerical investigation of the real and ideal gap profiles in the calculation of the pressure distortion coefficient and piston fall rate of an LNE 200 MPa pressure balance
WONGTHEP, Padipat; RABAULT, Thierry; NOGUERA, Ricardo; SARRAF, Christophe
This paper aims to investigate, by means of numerical simulation, the effect of gap profiles on the calculation of the pressure distortion coefficient (λ) and the piston fall rate (vf) of two piston-cylinder units used in a Laboratoire National de Métrologie et d'Essais (LNE) 200 MPa pressure balance. The ideal mean gap width between the piston and the cylinder was obtained after measuring the piston fall rate at a low pressure, while the piston radius was obtained from the cross-float experiments at a low pressure. The real gap width was obtained from dimensional measurements by measuring the diameter and straightness of the piston and the cylinder. The piston and cylinder radial distortions were calculated using the finite element method. The pressure distribution in the gap was calculated on the basis of the Navier-Stokes equation for Newtonian viscous flow. The results such as pressure distributions, radial distortions, the pressure distortion coefficient and the piston fall rate were presented for the free-deformation operating mode of the assemblies. The calculation resulted in ideal and real gap profiles indicating that the average pressure distortion coefficient was in good agreement within 0.017 × 10-6 MPa-1 and the calculations of piston fall rate depended on the gap profile especially at the inlet and outlet zones of the engagement length.
Tue, 01 Jan 2013 00:00:00 GMThttp://hdl.handle.net/10985/89142013-01-01T00:00:00ZWONGTHEP, PadipatRABAULT, ThierryNOGUERA, RicardoSARRAF, ChristopheThis paper aims to investigate, by means of numerical simulation, the effect of gap profiles on the calculation of the pressure distortion coefficient (λ) and the piston fall rate (vf) of two piston-cylinder units used in a Laboratoire National de Métrologie et d'Essais (LNE) 200 MPa pressure balance. The ideal mean gap width between the piston and the cylinder was obtained after measuring the piston fall rate at a low pressure, while the piston radius was obtained from the cross-float experiments at a low pressure. The real gap width was obtained from dimensional measurements by measuring the diameter and straightness of the piston and the cylinder. The piston and cylinder radial distortions were calculated using the finite element method. The pressure distribution in the gap was calculated on the basis of the Navier-Stokes equation for Newtonian viscous flow. The results such as pressure distributions, radial distortions, the pressure distortion coefficient and the piston fall rate were presented for the free-deformation operating mode of the assemblies. The calculation resulted in ideal and real gap profiles indicating that the average pressure distortion coefficient was in good agreement within 0.017 × 10-6 MPa-1 and the calculations of piston fall rate depended on the gap profile especially at the inlet and outlet zones of the engagement length.A new model of fluid flow to determine pressure balance characteristics
http://hdl.handle.net/10985/8900
A new model of fluid flow to determine pressure balance characteristics
WONGTHEP, Padipat; RABAULT, Thierry; NOGUERA, Ricardo; SARRAF, Christophe
Some projects such as the EUROMET project 463 have underlined the lack of agreement between experimental measurements and calculations by the finite element method (FEM), used to determine the piston fall rate of a high-pressure balance used in primary standards. This is significant because the piston fall rate is an essential parameter to characterize experimentally the mean gap between the piston and the cylinder and to determine the effective area (A p) at each pressure (p) point. By improving the method used to estimate the piston fall rate it is possible to improve the determination of the gap, the effective area and consequently the pressure distortion coefficient. One possible cause of the lack of agreement between the calculated and measured piston fall rates could be inappropriate modelling of the fluid flow. In fact, the former quasi-1D Stokes model assimilates the gap between the piston and the cylinder as formed by two parallel walls, which is an approximation. In addition, the velocity of the piston wall was neglected. In order to evaluate the influence of this model, the equations of the fluid flow are modified and are presented in this paper. Equations that were defined in a parallel-plane model are defined in an annular gap model. In addition to this, corrections due to the velocity of the piston wall are inserted. This research work is applied on a Desgranges et Huot DH 7594 piston-cylinder unit of PTB with a pressure up to 1 GPa, in the continuity of the EUROMET project 463 in order to quantify the influence of each correction that has been inserted in the new equations. This is carried out using the FEM. This analysis will allow us to evaluate the improvement of our knowledge of the behaviour of piston gauges and consequently to better evaluate the uncertainties due to the models.
Tue, 01 Jan 2013 00:00:00 GMThttp://hdl.handle.net/10985/89002013-01-01T00:00:00ZWONGTHEP, PadipatRABAULT, ThierryNOGUERA, RicardoSARRAF, ChristopheSome projects such as the EUROMET project 463 have underlined the lack of agreement between experimental measurements and calculations by the finite element method (FEM), used to determine the piston fall rate of a high-pressure balance used in primary standards. This is significant because the piston fall rate is an essential parameter to characterize experimentally the mean gap between the piston and the cylinder and to determine the effective area (A p) at each pressure (p) point. By improving the method used to estimate the piston fall rate it is possible to improve the determination of the gap, the effective area and consequently the pressure distortion coefficient. One possible cause of the lack of agreement between the calculated and measured piston fall rates could be inappropriate modelling of the fluid flow. In fact, the former quasi-1D Stokes model assimilates the gap between the piston and the cylinder as formed by two parallel walls, which is an approximation. In addition, the velocity of the piston wall was neglected. In order to evaluate the influence of this model, the equations of the fluid flow are modified and are presented in this paper. Equations that were defined in a parallel-plane model are defined in an annular gap model. In addition to this, corrections due to the velocity of the piston wall are inserted. This research work is applied on a Desgranges et Huot DH 7594 piston-cylinder unit of PTB with a pressure up to 1 GPa, in the continuity of the EUROMET project 463 in order to quantify the influence of each correction that has been inserted in the new equations. This is carried out using the FEM. This analysis will allow us to evaluate the improvement of our knowledge of the behaviour of piston gauges and consequently to better evaluate the uncertainties due to the models.