Laboratoire des Matériaux et Procédés (LaBoMaP): Soumissions récentes

Voici les éléments 105-111 de 372

    • Effect of the microstructure on the tribological properties of HIPed and PTA-welded Fe-based hardfacing alloy 
      Article dans une revue avec comité de lecture
      ARDIGO-BESNARD, Maria-Rosa; TELLIER, Arnold; BESNARD, Aurélien; CHATEAU-CORNU, Jean-Philippe (Elsevier BV, 2021)
      his work focuses on the comparison of the tribological properties of Norem02, a Fe-based hardfacing elaborated by hot isostatic pressing (HIP), a pressure-assisted sintering technique and by plasma transferred arc welding ...
    • Low-temperature plasma nitriding of martensitic stainless steel 
      Article dans une revue avec comité de lecture
      RAO, K. Ram Mohan; TRINADH, Kalimi; NOUVEAU, Corinne (2020)
      This study presents the plasma nitriding of Cr–Mo–V tool steel to protect it from environmental degradation. The steel samples after metallographic polishing were nitrided in the glow discharge plasma of N2 and H2 gas ...
    • Thermal modification kinetics and chemistry of poplar wood in dry and saturated steam media 
      Article dans une revue avec comité de lecture
      MARCON, Bertrand; TONDI, Gianluca; PROCINO, Lorenzo; GOLI, Giacomo (De Gruyter, 2021)
      This research work presents a modelling strategy to analyse thermal conversion rates of two thermal wood modification processes based on time-temperature superposition method. It gathers in a single study different original ...
    • Mechanical and Tribological Behaviors of Nanocomposite Titanium Nitrides Coatings 
      Article dans une revue avec comité de lecture
      BELGROUNE, Ahlam; AISSANI, Linda; SALHI, Faiza; ALHUSSEIN, Akram; NOUVEAU, Corinne (Trans Tech Publications, 2021)
      TiN coatings with a thickness of 2 μm were deposited using the magnetron sputtering has developed rapidly over the last decade in such a way that it has become an established process of choice for the deposition of a wide ...
    • A constitutive model for Ti6Al4V considering the state of stress and strain rate effects 
      Article dans une revue avec comité de lecture
      CHENG, Wenyu; MARTINS DO OUTEIRO, Jose Carlos; COSTES, Jean-Philippe; M'SAOUBI, Rachid; KARAOUNI, Habib; ASTAKHOV, Viktor (Elsevier, 2019)
      The predictability of manufacturing process simulation is highly dependent on the accuracy of the constitutive model to describe the mechanical behavior of the work material. The model should consider the most relevant ...
    • Enhancement of bending properties of Douglas-fir and poplar laminate veneer lumber (LVL) beams with carbon and basalt fibers reinforcement 
      Article dans une revue avec comité de lecture
      RESCALVO, Francisco J.; DURIOT, Robin; GALLEGO, Antolino; DENAUD, Louis; ccPOT, Guillaume (Elsevier, 2020)
      This paper presents the experimental results of the bending mechanical behavior (static and dynamic moduli, and maximum stress) of LVL (Laminated Veneer Lumber) beams reinforced with fiber polymer material (FRP). Different ...
    • Effect of Zr content on friction and wear behavior of Cr‐Zr‐N coating system 
      Article dans une revue avec comité de lecture
      FELLAH, Mamoun; AISSANI, Linda; ABDUL SAMAD, Mohammed; PURNAMA, Agung; DJEBAILI, Hamid; IOST, Alain; NOUVEAU, Corinne; ccMONTAGNE, Alex (Wiley, 2018)
      Nanostructured Cr‐Zr‐N thin film with different Zr content (0 to 48.8 at.%) was deposited, using an RF magnetron‐sputtering technique. The structural evolution and morphological changes were performed. The tribological ...