3-D Multi-Nodal Thermal Modelling for Fault-Tolerant Machine

OUENZERFI, Safouene; ZAHR, Hussein; TRABELSI, Mohamed; BOUBAKER, Riadh; HARMAND, Souad; SEMAIL, Eric

Communication avec acte

Auteur

OUENZERFI, Safouene
1303 Laboratoire d'Automatique, de Mécanique et d'Informatique industrielles et Humaines - UMR 8201 [LAMIH]

ZAHR, Hussein
13094 Institut de Recherche de l'Ecole Navale [IRENAV]

TRABELSI, Mohamed

BOUBAKER, Riadh
1303 Laboratoire d'Automatique, de Mécanique et d'Informatique industrielles et Humaines - UMR 8201 [LAMIH]

HARMAND, Souad
1303 Laboratoire d'Automatique, de Mécanique et d'Informatique industrielles et Humaines - UMR 8201 [LAMIH]

SEMAIL, Eric
13338 Laboratoire d’Électrotechnique et d’Électronique de Puissance - ULR 2697 [L2EP]

URI

http://hdl.handle.net/10985/18204

DOI

10.1109/ICIT.2019.8755164

Date

2019

Résumé

Even if intrinsically a five-phase machine can work with one opened phase, thermal constraints (temperatures in windings and Permanent Magnets) impose to decrease the mean torque in faulty operation mode. In order to elaborate optimum control which ensures safety and maximum torque, it is necessary to estimate in real-time the temperatures induced by the currents imposed in the remaining healthy windings of the machine. For a five-phase prototype, a multi-nodal thermal modelling which can take into account irregular losses and flow distribution has been developed. It is based on Electromagnetic FEM results for the losses and CFD calculation analysis. Results are presented in normal and faulty operation modes.

Fichier(s) constituant cette publication

Nom:: L2EP_ICIT_2019_SEMAIL.pdf
Taille:: 1.575Mo
Format:: PDF

Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

Laboratoire d'Electrotechnique et d'Electronique de Puissance (L2EP) de Lille

Visualiser des documents liés par titre, auteur, créateur et sujet.

Design Considerations of Five-Phase Machine with Double p/3p Polarity

Article dans une revue avec comité de lecture

GONG, Jinlin; ZAHR, Hussein; TRABELSI, Mohamed; ASLAN, Bassel; SEMAIL, Eric; SCUILLER, Franck (Institute of Electrical and Electronics Engineers, 2018)

In the context of traction drives with required torque transient capabilities and a classically wide flux weakening speed range, this paper gives design considerations of a particular Double-Polarity (DP) five-phase machine. ...
Five-Phase Bi-Harmonic PMSM Control under Voltage and Currents Limits

Communication avec acte

ZAHR, Hussein; TRABELSI, Mohamed; SEMAIL, Eric; NGUYEN, Ngac Ky (2017)

For a particular five-phase synchronous machine, this paper investigates the sensitivity of a vectorial control strategy on the required peak phase voltage whose value is fundamental for the choice of the DC bus voltage. ...
Homopolar Current’s Copper Losses Analysis for Different Modulations in Open-End Winding Five-Phase drives

Communication avec acte

DOS SANTOS MORAES, Tiago José; TRABELSI, Mohamed; ZAHR, Hussein; SEMAIL, Eric (IEEE, 2018)

This paper analyses the copper losses due to the homopolar current of a five-phase open-end winding machine supplied by a 10-leg inverter and a single DC voltage source. This topology can have non-null high frequency ...
Comparison and Analysis of Post-Fault Operation Modes in a Five-Phase PMSM Considering Thermal Behavior

Communication avec acte

ZAHR, Hussein; TRABELSI, Mohamed; SEMAIL, Eric (2018)

This paper presents a comparative evaluation of fault tolerant control strategies for a five-phase Permanent Magnet Synchronous Machine (PMSM) under an opened-phase fault mode. Two main classical Fault Tolerant Control ...
A bi-harmonic five-phase SPM machine with low ripple torque for marine propulsion

Communication avec acte

ZAHR, Hussein; SEMAIL, Eric; SCUILLER, Franck (2017)

This paper addresses the design of a bi-harmonic five-phase Surface-mounted Permanent Magnet (SPM) machine for marine propulsion. The bi-harmonic characteristic results from the particular 20 slots-8 poles configuration ...