• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • Voir le document
  • Accueil de SAM
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Flip-chip technology at room temperature: A new design of microtube-based interconnect for improved mechanical and electrical properties

Article dans une revue avec comité de lecture
Auteur
DESBORDES, Cloé
1042703 Université Grenoble Alpes [UGA]
ccPESCI, Raphaël
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
ccPIOTROWSKI, Boris
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
MAILLIART, Olivier
40211 Département d'Optronique [DOPT]
1042703 Université Grenoble Alpes [UGA]
RAPHOZ, Natacha
1042703 Université Grenoble Alpes [UGA]

URI
http://hdl.handle.net/10985/25421
DOI
10.1016/j.sna.2024.115674
Date
2024-10
Journal
Sensors and Actuators: A. Physical

Résumé

Flip-chip assembly of photonic components can be achieved at room temperature by using 10 μm pitch interconnects made of metallised oxide microtubes inserted into ductile reception pads. In order to reduce the electrical resistance of interconnects and the assembly force required, interconnect design in regard to geometry and materials used are optimised through electrical and mechanical finite elements (FEM) simulations. To reduce electrical resistance, one may increase the metallisation thickness or microtube inner diameter. To minimise the assembly force, reducing the reception pad diameter is recommended. Experiments on silicon (Si) test vehicles are conducted to validate these predictions; they indicate that there is no short circuit, with an effectiveness of 100 %. This is achieved first through the assembly of Al-0.5 %wCu metallised oxide microtubes into Al-0.5 %wCu reception pads, using a force less than 10 mN/interconnect and proved to have a resistance of 230 mΩ. Second, with gold (Au) metallised oxide microtubes in indium (In) pads assembled with a force less than 0.7 mN/ interconnect. Last interconnects have a resistance of 670 mΩ/interconnect and can still be reduced to 500 mΩ by 2 h annealing at 100 ◦C.

Fichier(s) constituant cette publication

Nom:
LEM3_SAA_2024_PESCI.pdf
Taille:
6.495Mo
Format:
PDF
Fin d'embargo:
2025-05-01
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Mechanical properties of a nanoporous membrane used in implantable medical devices. Correlation between experimental characterization and 2D numerical simulation 
    Article dans une revue avec comité de lecture
    CRISTOFARI, François; PIOTROWSKI, Boris; ccPESCI, Raphaël (Elsevier, 2017)
    Nanoporous membranes are used for the elaboration of implantable medical devices. In order to guaranty their integrity after implantation in a patient body, it is necessary to characterize the microstructure and the ...
  • Multilayer CdHgTe-based infrared detector: 2D/3D microtomography, synchrotron emission and finite element modelling with stress distribution at room temperature and 100 K 
    Article dans une revue avec comité de lecture
    LEBAUDY, Anne-Laure; PIOTROWSKI, Boris; ccPESCI, Raphaël (Elsevier, 2020)
    The mechanical behaviour of a CdHgTe-based infrared detector was evaluated after processing at several temperatures to determine the impact of thermomechanical loading on residual stress and reliability. The architecture ...
  • Micromachine d'essais mécaniques de type traction et compression ayant une accessibilité optimisée 
    Brevet
    BOMONT, Olivier; WARY, Marc; BIANCHIN, Jeremy; SIMON, Lionel; BOEHM, Daniel; HECKER, Jean-Michel; PEIFFERT, Xavier; ccPESCI, Raphaël (2015)
    L'invention concerne une micromachine de traction destinée à être utilisée dans une enceinte de microscope électronique à balayage ou avec un appareil de diffraction, comportant deux mors (1) portés par deux supports, ...
  • Grain and phase stress criteria for behaviour and cleavage in duplex and bainitic steels 
    Article dans une revue avec comité de lecture
    INAL, Karim; LEBRUN, Jean-Lou; DIARD, Olivier; MASSON, Renaud; ccPESCI, Raphaël (Wiley-Blackwell, 2006)
    Stress analyses by X-ray diffraction are performed on a cast duplex (32% ferrite) stainless steel elbow and a bainitic (95% ferrite) pressure vessel steel. During an in situ tensile test, micrographic observations are made ...
  • Experimental and numerical investigation of local stress and strain heterogeneities in a bainitic steel 
    Conférence invitée
    DIARD, Olivier; MATHIEU, Jean-Philippe; STUDER, Vincent; INAL, Karim; ccPESCI, Raphaël (2005)
    A specific in-situ tensile device has been set up in an X-Ray diffractometer. Stress can be measured at low temperature during loading in the baintic steel and in the ferritic phase. A two-scale modeling has been proposed ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales