• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental and numerical analysis of the selective laser sintering (SLS) of PA12 and PEKK semi-crystalline polymers

Article dans une revue avec comité de lecture
Auteur
PEYRE, Patrice
ROUCHAUSSE, Yann
DEFAUCHY, Denis
ccREGNIER, Gilles
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]

URI
http://hdl.handle.net/10985/11222
DOI
10.1016/j.jmatprotec.2015.04.030
Date
2015
Journal
Journal of Materials Processing Technology

Résumé

A dual experimental-numerical approach was carried out to estimate thermal cycles and resulting fusion depths obtained during the selective laser sintering (SLS) of two polymers: PA12 and PEKK. The validation of thermal cycles was obtained by considering fusion depths on single layers for different experimental conditions and temperature measurements with IR thermal camera. It was shown that a simple Beer-Lambert's heat deposit equation incorporating an extinction coefficient determined experimentally and an efficiency ratio including both laser absorption and diffusion in the powder bed were sufficient for determining accurately fusion depths, and heat cycles for the two polymers. This allowed determining optimum process conditions for manufacturing additive layers on a specifically-designed SLS set-up.

Fichier(s) constituant cette publication

Nom:
PIMM - JMPT - PEYRE - 2015.pdf
Taille:
3.828Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Experimental and numerical analysis of the selective laser sintering (SLS) of PA12 and PEKK semi-crystalline polymers 
    Article dans une revue avec comité de lecture
    ROUCHAUSSE, Yann; PEYRE, Patrice; DEFAUCHY, Denis; ccREGNIER, Gilles (Elsevier, 2015)
    A dual experimental-numerical approach was carried out to estimate thermal cycles and resulting fusion depths obtained during the selective laser sintering (SLS) of two polymers: PA12 and PEKK. The validation of thermal ...
  • Coalescence modeling and experimental validation of sintering of thermoplastic polyamide fibers 
    Article dans une revue avec comité de lecture
    XU, Fan; LI, Xin; DEFAUCHY, Denis; ccREGNIER, Gilles (2013)
    In order to study the coalescence mechanisms of thermoplastic polymer powders, a 2D mathematical model has been established based on Frenkel, Eshelby and Pokluda’s model. Sintering experiments have been carried out by using ...
  • Study of laser interaction in water flow confinement at high repetition rate 
    Article dans une revue avec comité de lecture
    BERTHE, Laurent; COURAPIED, Damien; EL KARNIGHI, Samy; PEYRE, Patrice; GORNY, Cyril; ROUCHAUSSE, Yann (Laser Institute of America, 2017)
    This paper presents a study on the confined interaction with water flow for two successive laser pulses. The dynamic of the renewal of water films after shock produced by the laser is observed using a high speed camera. ...
  • Amélioration de l'état de surface de pièces obtenues en fabrication directe par projection laser à l'aide d'un modèle numérique thermohydraulique 2D 
    Communication avec acte
    MORVILLE, Simon; CARIN, Muriel; LE MASSON, Philippe; CARRON, Denis; PEYRE, Patrice; GHARBI, Myriam; FABBRO, Rémy (Société Française de Thermique / Congrès Français de Thermique - Thermique en conditions extrêmes, 29 mai - 1er juin 2012, Bordeaux, 2012)
    La Fabrication Directe par Projection Laser (FDPL) est un procédé novateur issu du prototypage rapide et du rechargement laser. Cette technologie permet de fabriquer des pièces 3D pleinement densifiées par injection de ...
  • Etude thermique des bains liquides et son effet sur l’état de surface des pièces fabriquées par le procédé de Fabrication Directe par Projection Laser (FDPL) 
    Communication avec acte
    GHARBI, Myriam; PEYRE, Patrice; GORNY, Cyril; FABBRO, Rémy; MULLER, Maryse; CARIN, Muriel; MORVILLE, Simon; CARRON, Denis; LE MASSON, Philippe (Société Française de Thermique / Congrès Français de Thermique - Thermique en conditions extrêmes, 29 mai - 1er juin 2012, Bordeaux, 2012)
    La fabrication directe par projection laser (FDPL) est un procédé de prototypage rapide et de fabrication des petites séries de pièces complexes, par simple interaction entre un faisceau laser, un substrat, et une poudre ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales