Laboratoire d'Electrotechnique et d'Electronique de Puissance (L2EP) de Lille: Soumissions récentes

Voici les éléments 57-63 de 327

    • Influence of laser powder bed fusion process conditions and resulting microstructures on the electromagnetic properties of a 16MnCr5 steel 
      Article dans une revue avec comité de lecture
      DUPUY, Corinne; BENABOU, Abdelkader; SHIHAB, Sylvain; MESSAL, O.; PEYRE, Patrice; ccCLENET, Stephane (Elsevier, 2021)
      16MnCr5 steel parts were additively manufactured by laser powder bed fusion in order to investigate the effect of microstructure on electromagnetic properties. As process parameters have a direct impact on the obtained ...
    • Torque Ripple Eliminations for Multiphase Nonsinusoidal Permanent Magnet Synchronous Machines 
      Communication avec acte
      VU, DUC TAN; NGUYEN, Ngac Ky; ccSEMAIL, Eric (IEEE, 2021)
      This paper is to propose a control scheme, a combination of the classical field-oriented control (FOC) technique and artificial intelligence (AI), to obtain constant torques in multiphase non-sinusoidal permanent magnet ...
    • Slinky stator : The impact of manufacturing process on the magnetic properties 
      Communication avec acte
      EL YOUSSEF, Mohamad; VAN GORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; LAVALLEY, Yannick; COUR, Christiane; LECUPPE, Thomas; ccCLENET, Stephane (IEEE, 2017)
      The manufacturing of a slinky stator core is the result of a sequence of difference processes: straightening, punching, rolling….. It has been shown in the literature that manufacturing processes lead to a degradation of ...
    • Experimental set up for magnetomechanical measurements with a closed flux path sample 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; VAN GORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; ccCLENET, Stephane (De Gruyter, 2020)
      In this article, an experimental procedure is presented to handle magnetic measurements under uniaxial tensile stress reaching the plastic domain. The main advantage of the proposed procedure is that it does not require ...
    • The effect of punching on electrical machine 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; BENABOU, AbdelKader; VAN GORP, Adrien; FAVEROLLE, Pierre; MIPO, Jean-Claude; LAVALLEY, Yannick; LECUPPE, Thomas; ccCOOREVITS, Thierry; ccCLENET, Stephane (IOS Press, 2019)
      This work enlightens the impact of punching on a specific stator performances. Two specimens type are withdrawn from a M330A35 punched lamination sheet. One type represents a closed magnetic circuit while the other represents ...
    • Sensorless Control for Non-sinusoidal Five-phase Interior PMSM based on Sliding Mode Observer 
      Article dans une revue avec comité de lecture
      MINI, Youssouf; ccSEMAIL, Eric; NGUYEN, Ngac Ky (Lavoisier, 2021)
      This paper proposes a sensorless control strategy based on Sliding Mode Observer (SMO) for a Five-phase Interior Permanent Magnet Synchronous Machine (FIPMSM), with a consideration of the third harmonic component. Compared ...
    • Improving global ferromagnetic characteristics of laminations by heterogeneous deformation 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; VANGORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; ccCLENET, Stephane (Institute of Electrical and Electronics Engineers, 2021)
      In this paper, an experimental procedure is presented in order to handle magnetic measurements under uniaxial tensile stress reaching the plastic domain. The main advantage of the proposed procedure is that it does not ...