• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

A new insight on induced-tribological behaviour of hypereutectic Al-Si alloys manufactured by selective laser melting

Article dans une revue avec comité de lecture
Auteur
KANG, Nan
ccEL MANSORI, Mohamed
211915 Mechanics surfaces and materials processing [MSMP]
301080 Texas A&M University [College Station]

URI
http://hdl.handle.net/10985/18720
DOI
10.1016/j.triboint.2019.04.035
Date
2019
Journal
Tribology International

Résumé

In this work, the tribological behaviour of selective laser melting (SLM) processed hypereutectic Al-Si alloy is investigated by the ball on disc test with focus on the effect of silicon content (18 and 50 wt %). Different from the conventional casted sample, the SLM processed sample shows an ultra-fine microstructure with silicon size inferior to 5 μm. Indeed, the SLM processed hypereutectic Al-Si alloy illustrates a pseudo-eutectic microstructure consisted by supersaturated Al(Si) and primary silicon. Both the SLM processed Al-18Si and Al-50Si presents low wear rate about of 7.0 and 8.1◊10−4 mm3/(N◊m) respectively. Moreover, the wear mechanisms of conventional casted and SLM processed hypereutectic Al-Si alloys are compared and discussed.

Fichier(s) constituant cette publication

Nom:
MSMP_TI_2019_ELMANSORI.pdf
Taille:
10.24Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Nano-wear-induced behavior of selective laser melting commercial pure titanium 
    Article dans une revue avec comité de lecture
    KANG, Nan; ccEL MANSORI, Mohamed; ccCONIGLIO, Nicolas; CODDET, Christian (Elsevier BV, 2018)
    In this work, the nano-wear-induced behavior of selective laser melting (SLM) processed commercial pure titanium was investigated under several applied loads from 1 mN to 100 mN. The dense (over 99%) commercial pure titanium ...
  • Anisotropic high cycle fatigue property of Sc and Zr-modified Al-Mg alloy fabricated by laser powder bed fusion 
    Article dans une revue avec comité de lecture
    QIN, Zehao; KANG, Nan; ccEL MANSORI, Mohamed; WANG, Zihong; WANG, Haoxiang; LIN, Xin; CHEN, Jing; HUANG, Weidong (Elsevier BV, 2022-01)
    This work investigates the defects (pore and lack of fusion), microstructure, and fatigue properties of Sc and Zr-modified Al–Mg alloy on different building directions fabricated by laser powder bed fusion (LPBF). The ...
  • Intrinsic heat treatment induced graded surficial microstructure and tribological properties of selective laser melted titanium 
    Article dans une revue avec comité de lecture
    KANG, Nan; CAO, Yang; ZHAO, Chunling; ZHAO, Yu; LIN, Chin; CODDET, Christian; ccEL MANSORI, Mohamed; ccCONIGLIO, Nicolas (American Society of Mechanical Engineers, 2021)
    In the course of the selective laser melting (SLM) process, the part is built layer by layer involving partial re-melting/heating of the previous layer, called as intrinsic heat treatment. Therefore, superficial properties ...
  • Effect of selective post-aging treatment on subsurface damage of quasicrystal reinforced Al composite manufactured by selective laser melting 
    Article dans une revue avec comité de lecture
    ccKANG, Nan; LU, J.L.; LIN, X.; HUANG, W.D.; ccEL MANSORI, Mohamed (Elsevier, 2019)
    In this work, Al-Fe-Cr quasicrystal reinforced Al matrix composite was in-situ prepared by using selective laser melting from powder mixture of Al-Cu-Fe-Cr quasicrystal and pure Al. The effect of selective post-aging ...
  • Selective laser melting of tungsten carbide reinforced maraging steel composite 
    Article dans une revue avec comité de lecture
    KANG, Nan; MA, Wenyou; LI, Fuhai; LIU, Min; LIAO, Hanlin; ccEL MANSORI, Mohamed; ccHERAUD, Lorene (Elsevier, 2018)
    In this work, tungsten carbide (WC) reinforced maraging steel matrix composites were in-situ manufactured by selective laser melting (SLM) from powder mixture. The SLM processed samples presented high relative density (over ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales