Usinage grande vitesse avec maîtrise globale du procédé appliqué aux matériaux difficiles et surfaces complexes. Usinage et mise en forme du bois. Traitements superficiels et optimisation des matériaux et alliages.
Plus d'informations sur le site du LaBoMaP :
labomap.ensam.eu

Recent Submissions

• 

  Effect of Ar/N2 flow ratio on the microstructure and mechanical properties of Ti-Cr-N coatings deposited by DC magnetron sputtering on AISI D2 tool steels 

  Article dans une revue avec comité de lecture

  KEHAL, Abdelkrim; SAOULA, Nadia; ABAIDIA, Seddik-El-Hak; NOUVEAU, Corinne (Elsevier BV, 2021)

  Ti-Cr-N coatings were deposited on Si (100) and AISI D2 tool steel substrates by reactive DC magnetron co- sputtering technique from titanium and chromium target in mixed Ar/N2 atmosphere. The Ar/N2 ...
• 

  Generalized cutting force model for peripheral milling of wood, based on the effect of density, uncut chip cross section, grain orientation and tool helix angle 

  Article dans une revue avec comité de lecture

  CURTI, Rémi; MARCON, Bertand; DENAUD, Louis; TOGNI, Marco; FURFERI, Rocco; GOLI, Giacomo (Springer Verlag, 2021)

  The influence of the grain angle on the cutting force when milling wood is not yet detailed, apart from particular cases (end-grain, parallel to the grain, or in some rare cases 45°-cut). Thus, setting-up wood machining ...
• 

  Multi-physical analysis of the electrochemical behaviour of OFHC copper surfaces obtained by orthogonal cutting 

  Article dans une revue avec comité de lecture

  DENGUIR, Lamice A.; OUTEIRO, Jose C.; FROMENTIN, Guillaume (Taylor and Francis, 2020)

  As mechanical, physical, and microstructural properties of metals can be significantly affected by the machining process, electrochemical properties and corrosion resistance are consequently altered. Manufacturers should ...
• 

  Machining and heat treatment as post-processing strategies for Ni-superalloys structures fabricated using direct energy deposition 

  Article dans une revue avec comité de lecture

  CARERI, Francesco; IMBROGNO, Stano; UMBRELLO, Domenico; ATTALLAH, Moataz M.; OUTEIRO, José; BATISTA, António C. (Elsevier, 2021)

  The aim of this study is to determine the most suitable post-processing routines to enhance the surface integrity of components produced with Inconel 718 superalloy by additive manufacturing. The components were fabri­cated ...
• 

  Density, extractives and decay resistance variabilities within branch wood from four agroforestry hardwood species 

  Article dans une revue avec comité de lecture

  TERRASSE, F; BRANCHERIAU, L; MARCHAL, R; BOUTAHAR, N; LOTTE, S; GUIBAL, D; PIGNOLET, L; CANDELIER, K (Italian Society of Sivilculture and Forest Ecology (SISEF), 2021)

  Agroforestry practices like pruning trees to control the light flux to crops produce every year a large volume of branches which is valorized by farmers as mulching or energy fuel. However, according to the literature, the ...
• 

  The Effect of Bilayer Periods and Their Thickness in Magnetron Sputtering Protective Multilayer Coatings for Tribological Applications 

  Article dans une revue avec comité de lecture

  AOUADI, Khalil; NOUVEAU, Corinne; BESNARD, Aurélien; TLILI, Brahim; MONTAGNE, Alex; CHAFRA, Moez (Springer Science and Business Media LLC, 2021)

  CrN/CrAlN thin films were deposited by DC reactive magnetron sputtering. The influence of CrN/CrAlN bilayer thickness on the microstructure, mechanical, and tribological properties was studied. Crystallinity of the layers ...
• 

  Effects of plasma nitriding on low alloy Cr-Mo-V steel 

  Article dans une revue avec comité de lecture

  TRINADH, Kalimi; NOUVEAU, Corinne; RAO, K. Ram Mohan (Elsevier, 2021)

  In this study the effects on resistance to corrosion of a low alloy steel after plasma nitriding has been reported. Nitriding was performed at a low temperature of 450 °C and also at 520 °C for the same duration of 10 h ...

View more