Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM): Soumissions récentes

Voici les éléments 701-707 de 1302

    • Study of laser interaction in water flow confinement at high repetition rate 
      Article dans une revue avec comité de lecture
      BERTHE, Laurent; COURAPIED, Damien; EL KARNIGHI, Samy; PEYRE, Patrice; GORNY, Cyril; ROUCHAUSSE, Yann (Laser Institute of America, 2017)
      This paper presents a study on the confined interaction with water flow for two successive laser pulses. The dynamic of the renewal of water films after shock produced by the laser is observed using a high speed camera. ...
    • Rheokinetic of polyurethane crosslinking time-temperature-transformation diagram for rotational molding 
      Article dans une revue avec comité de lecture
      FARZANEH, Sedigheh; RIVIERE, Sylvain; ccTCHARKHTCHI, Abbas (Wiley, 2012)
      In this work, the rheokinetic of polyurethane crosslinking was studied by different methods: differential scanning calorimetric (DSC), rheometry, and infrared spectrometry. The conversion ratio and the glass transition ...
    • Computational Homogenization of Architectured Materials 
      Chapitre d'ouvrage scientifique
      DIRRENBERGER, Justin; FOREST, Samuel; JEULIN, Dominique (Springer New York, 2019)
      Architectured materials involve geometrically engineered distributions of microstructural phases at a scale comparable to the scale of the component, thus calling for new models in order to determine the effective properties ...
    • Laser impulse coupling measurements at 400 fs and 80 ps using the LULI facility at 1057 nm wavelength 
      Article dans une revue avec comité de lecture
      PHIPPS, Claude R.; BOUSTIE, Michel; CHEVALIER, Jean Marc; BATON, Sophie D.; BRAMBRINK, Erik; BERTHE, Laurent; ccSCHNEIDER, Matthieu; VIDEAU, Laurent; BOYER, Séverine A.E.; SCHARRING, Stefan (American Institute of Physics, 2017)
      At the École Polytechnique « LULI » facility, we have measured the impulse coupling coefficient Cm (target momentum per joule of incident laser light) with several target materials in vacuum, at 1057 nm and 400 fs and 80 ...
    • Wetting by liquid sodium and fracture path analysis of sodium induced embrittlement of 304L stainless steel 
      Article dans une revue avec comité de lecture
      BARKIA, Bassem; AUGER, Thierry; COUROUAU, Jean Louis; BOURGON, Julie (Cambridge University Press (CUP), 2018)
      The wettability of the 304L steel is an important parameter in Liquid Metal Embrittlement studies. Empirically, it is found to be greatly enhanced by pre-exposure to oxygenated liquid sodium. The corrosion interface formed ...
    • Thermal cycling of cold-pressed PTFE compacts: Reversible and irreversible behavior 
      Article dans une revue avec comité de lecture
      GUENOUN, Gabriel; FAOU, Jean-Yvon; SCHMITT, Nicolas; ccREGNIER, Gilles (Elsevier, 2019)
      Cold uniaxial pressed PTFE compacts were subjected to thermal cycles of increasing maximum temperature below melting temperature, and thermal expansion was followed in both the compaction and transverse directions. The ...
    • Beware of the Flory parameter to characterize polymer-polymer interactions: A critical reexamination of the experimental literature 
      Article dans une revue avec comité de lecture
      MIQUELARD-GARNIER, Guillaume; ccROLAND, Sébastien (Elsevier, 2016)
      Methods for obtaining Flory parameter (χ) values for polymer blends or blocks are critically examined, for three simple systems (polystyrene/poly(methyl methacrylate), polystyrene/polycarbonate, poly(methyl methacrylate) ...