Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM): Soumissions récentes

Voici les éléments 960-966 de 1243

    • Platicizer effect on network structure and hydrolytic degradation 
      Article dans une revue avec comité de lecture
      DERUE, Isabelle; GILORMINI, Pierre; VERDU, Jacques; VAULOT, Cyril; COQUILLAT, Marie; DESGARDIN, Nancy; VANDENBROUKE, Aude; ccRICHAUD, Emmanuel (Elsevier, 2015)
      The hydrolytic degradation of fully cured polyester-urethane networks polymerized in the presence of several weight ratios of triacetin was monitored by the residual concentration in elastically active chains obtained from ...
    • Supramolecular assembly of gelatin and inorganic polyanions: Fine-tuning the mechanical properties of nanocomposites by varying their composition and microstructure 
      Article dans une revue avec comité de lecture
      BAROUDI, Imane; SIMONNET-JÉGAT, Corine; ROCH-MARCHAL, Catherine; LECLERC-LARONZE, Nathalie; LIVAGE, Carine; MARTINEAU, Charlotte; GERVAIS, Christel; CADOT, Emmanuel; CARN, Florent; STEUNOU, Nathalie; ccFAYOLLE, Bruno (American Chemical Society, 2015)
      A series of bionanocomposites has been synthesized through a complex coacervation process inducing the assembly of gelatin with a wide range of inorganic polyanions (IPyAs) differing by their diameter and charge and including ...
    • Polyoxymethylene additives 
      Chapitre d'ouvrage scientifique
      ccRICHAUD, Emmanuel (Wiley - Scrivener Publishing, 2014)
      This chapter presents a review of the role of several additives on POM processing (lubricating agents, processing aids, nucleating agents), performances (fillers, impact modifiers) and lifetime increase (antioxidants, ...
    • Generation and characterization of T40/A5754 interfaces with lasers 
      Article dans une revue avec comité de lecture
      PEYRE, Patrice; BERTHE, Laurent; POUZET, Sébastien; SALLAMAND, Pierre; TOMASHCHUK, Iryna; ccDAL, Morgan (Elsevier, 2014)
      Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser ...
    • Effect of crystallization on barrier properties of formulated polylactide 
      Article dans une revue avec comité de lecture
      COURGNEAU, Cécile; DOMENEK, Sandra; LEBOSSÉ, Régis; GUINAULT, Alain; AVÉROUS, Luc; DUCRUET, Violette (Wiley, 2012)
      Polylactide (PLA), a biodegradable polymer obtained from biomass, was formulated with a nucleating agent, talc, and a plasticizer, acetyl tributyl citrate, and cold crystallized in α and α′ form. The barrier properties of ...
    • Problem of elastic anisotropy and stacking faults in stress analysis using multireflection grazing-incidence X-ray diffraction 
      Article dans une revue avec comité de lecture
      MARCISZKO, Marianna; BACZMANSKI, Andrzej; MIROSŁAW, Wrobel; SEILER, Wilfrid; WRONSKI, Sebastian; WAWSZCZAK, Roman; ccBRAHAM, Chedly (International Union of Crystallography, 2015)
      Multireflection grazing-incidence X-ray diffraction (MGIXD) was used to determine the stress- and strain-free lattice parameter in the surface layer of mechanically treated (polished and ground) tungsten and austenitic ...
    • High strain rate visco-damageable behavior of Advanced Sheet Molding Compound (A-SMC) under tension 
      Article dans une revue avec comité de lecture
      SHIRINBAYAN, Mohammadali; SUROWIEC, Benjamin; BOCQUET, Michel; ccTCHARKHTCHI, Abbas; ccFITOUSSI, Joseph; ccMERAGHNI, Fodil (Elsevier, 2015)
      Advanced Sheet Molding Compound (A-SMC) is a serious composite material candidate for structural automotive parts. It has a thermoset matrix and consists of high weight content of glass fibers (50% in mass) compared to ...