• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • View Item
  • Home
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Simulation and measurement of residual stress and warpage in a HgCdTe-based infrared detector at 100 K

Article dans une revue avec comité de lecture
Author
DUPERREX, Lucas
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
1042703 Université Grenoble Alpes [UGA]
PESCI, Raphaël
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
LE BOTERF, Pascal
1002698 LYNRED (Veurey-Voroize)
MAILLIART, Olivier
1042703 Université Grenoble Alpes [UGA]

URI
http://hdl.handle.net/10985/20195
DOI
10.1016/j.msea.2021.141148
Date
2021
Journal
Materials Science and Engineering: A

Abstract

A thermomechanical analysis on a 320 × 256, 30 μm pitch, middle wave infrared detector operating at 100 K is conducted. The stress induced in the HgCdTe single crystal layer needs to be minimized to avoid electro-optical perturbations and the planarity of the detector has to respect strict optical requirements. The work includes stress determination by X-ray-diffraction (XRD), warpage measurements with laser scanning, analytical calculation and finite-element modelling. The hybridized detector is studied both alone and after being glued to an AlN hosting substrate. The results show that the initial stress in HgCdTe at room temperature is biaxial for all samples, with either tensile or compressive values (±10 MPa), mainly due to the lattice mismatch during epitaxy from CdZnTe. A stress increase of +45 MPa is induced after cooling to 100 K, with a maximum value of 57 MPa. The warpage of the hybridized circuit is then about 2.5 μm and is reduced after being glued to the hosting substrate. Finally, the model is used to extrapolate the behavior of such a detector for larger formats until 2 K2; there is no significant impact on the stress in the HgCdTe layer, but warpage increases proportionally to the squared diagonal of the detector.

Files in this item

Name:
LEM3_MSE_2021_PESCI.pdf
Size:
4.908Mb
Format:
PDF
Embargoed until:
2021-10-01
View/Open

Collections

  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)

Related items

Showing items related by title, author, creator and subject.

  • Micromachine d'essais mécaniques de type traction et compression ayant une accessibilité optimisée 
    Brevet
    PESCI, Raphaël; BOMONT, Olivier; WARY, Marc; BIANCHIN, Jeremy; SIMON, Lionel; BOEHM, Daniel; HECKER, Jean-Michel; PEIFFERT, Xavier (2015)
    L'invention concerne une micromachine de traction destinée à être utilisée dans une enceinte de microscope électronique à balayage ou avec un appareil de diffraction, comportant deux mors (1) portés par deux supports, ...
  • Experimental and numerical investigation of local stress and strain heterogeneities in a bainitic steel 
    Conférence invitée
    DIARD, Olivier; MATHIEU, Jean-Philippe; STUDER, Vincent; PESCI, Raphaël; INAL, Karim (2005)
    A specific in-situ tensile device has been set up in an X-Ray diffractometer. Stress can be measured at low temperature during loading in the baintic steel and in the ferritic phase. A two-scale modeling has been proposed ...
  • Lattice strain measurements using synchrotron diffraction to calibrate a micromechanical modeling in a ferrite–cementite steel 
    Article dans une revue avec comité de lecture
    TAUPIN, Vincent; PESCI, Raphaël; BERBENNI, Stéphane; BERVEILLER, Sophie; OUAHAB, Razane; BOUAZIZ, Olivier (Elsevier, 2013)
    In situ tensile tests were performed at room temperature on a ferrite–cementite steel specifically designed for this study. The evolution of the average stress in ferrite during loading was analyzed by X-ray diffraction.Lattice ...
  • Grain and phase stress criteria for behaviour and cleavage in duplex and bainitic steels 
    Article dans une revue avec comité de lecture
    INAL, Karim; PESCI, Raphaël; LEBRUN, Jean-Lou; DIARD, Olivier; MASSON, Renaud (Wiley-Blackwell, 2006)
    Stress analyses by X-ray diffraction are performed on a cast duplex (32% ferrite) stainless steel elbow and a bainitic (95% ferrite) pressure vessel steel. During an in situ tensile test, micrographic observations are made ...
  • Reuse of medical face masks in domestic and community settings without sacrificing safety: Ecological and economical lessons from the Covid-19 pandemic 
    Article dans une revue avec comité de lecture
    ALCARAZ, Jean-Pierre; LE COQ, Laurence; POURCHEZ, Jérémie; THOMAS, Dominique; CHAZELET, Sandrine; BOUDRY, Isabelle; BARBADO, Maud; SILVENT, Sophie; DESSALE, Claire; ANTOINE, Fabienne; GUIMIER-PINGAULT, Catherine; CORTELLA, Laurent; ROUIF, Sophie; BARDIN-MONNIER, Nathalie; CHARVET, Augustin; DUFAUD, Olivier; LECLERC, Lara; MONTIGAUD, Yoann; LAURENT, Coralie; VERHOEVEN, Paul; JOUBERT, Aurélie; BOUHANGUEL, Ala; ANDRES, Yves; GAFFÉ, Joël; MARTIN, Donald K.; HUET, Christophe; BOISSET, Sandrine; MAURIN, Max; RUMEAU, Pascal; CHARLOT, Frédéric; RICHAUD, Emmanuel; MOREAU-GAUDRY, Alexandre; BONNETERRE, Vincent; CINQUIN, Philippe; LANDELLE, Caroline (Elsevier, 2021)
    The need for personal protective equipment increased exponentially in response to the Covid-19 pandemic. To cope with the mask shortage during springtime 2020, a French consortium was created to find ways to reuse medical ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales