• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • View Item
  • Home
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Influence of the carburization time on the structural and mechanical properties of XC20 steel

Article dans une revue avec comité de lecture
Author
ABDENOUR, Saoudi
559962 University of Khenchela [University of Khenchela]
LINDA, Aissani
301037 Université Larbi-Ben-Mhidi [Oum-El-Bouaghi] [OEB]
559962 University of Khenchela [University of Khenchela]
OUALID, Chahaoui
559962 University of Khenchela [University of Khenchela]
ALI, Bestandji
SALAH, Louafi Mohammed
559962 University of Khenchela [University of Khenchela]
HAMID, Djebaili
559962 University of Khenchela [University of Khenchela]
FRANCISCO, Chinesta
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]

URI
http://hdl.handle.net/10985/20936
DOI
10.1088/2053-1591/ac1ece
Date
2021
Journal
Materials Research Express

Abstract

This study focuses on the effect of carburization time on the structural and mechanical properties of low carbon XC20 mild steel (C. Wt.% <0.25). The XC20 steel was carburized with activated carbon with a carbon potential Cp1 = 1.1%, at 910 C at different carburization times of 2, 4 and 6 h. The results obtained show that XC20 steel (non-carburized) has a ferrite-pearlitic structure with a hardness and a Young's modulus of the order of (150 HV, 26 KN/mm2). After carburization, the structure of the carburized layer is transformed in martensite (Fe γ) in which cementite (Fe3C) is imbricated. The depth of the carburized layer and the amount of carbon on the surface gradually increase with increasing carburization time. In addition, the carburized XC20 steel becomes hard and brittle where the hardness and Young's modulus have been increased for a high holding time until reaching maximum values (845 HV, 48 KN mm-2) after 6 h of carburization . However, the toughness of XC20 steel has been reduced from 163 to 40 J cm-2.

Files in this item

Name:
PIMM_MRE_ABDENOUR_2021_OPENACC ...
Size:
1.994Mb
Format:
PDF
View/Open

Collections

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Related items

Showing items related by title, author, creator and subject.

  • Thermal treatment effect on structural and mechanical properties of Cr–C coatings 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; ZAIRI, Amel; TOUHAMI, Mohamed Zine; DJEBAILI, Hamid; IOST, Alain; ABDUL SAMAD, Mohammed; NOUVEAU, Corinne; ccMONTAGNE, Alex (Maney Publishing, 2018)
    In the present study, the effect of thermal treatment on the mechanical and structural properties of chromium carbide coatings with different thicknesses is evaluated. The coatings were deposited by cathodic magnetron ...
  • Effect of Zr content on friction and wear behavior of Cr‐Zr‐N coating system 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; ABDUL SAMAD, Mohammed; PURNAMA, Agung; DJEBAILI, Hamid; IOST, Alain; NOUVEAU, Corinne; ccMONTAGNE, Alex (Wiley, 2018)
    Nanostructured Cr‐Zr‐N thin film with different Zr content (0 to 48.8 at.%) was deposited, using an RF magnetron‐sputtering technique. The structural evolution and morphological changes were performed. The tribological ...
  • Kinetic Monte Carlo simulation of random deposition and scaling behavior with respect to the germination length 
    Article dans une revue avec comité de lecture
    SAOUDI, Abdenour; AISSANI, Linda; SORBA, Grégoire; ccCHINESTA SORIA, Francisco (World Scientific Pub Co Pte Lt, 2021)
    This work aims at analyzing the scaling behavior and develop correlations during surface growing for different germination lengths. The surface growing by random deposition is simulated using a kinetic Monte Carlo approach, ...
  • Influence of vanadium on structure, 
    Article dans une revue avec comité de lecture
    AISSANI, Linda; WALOCK, Michael J.; DJEBAILI, Hamid; DJELLOUL, Ahmed Daoud; NOUVEAU, Corinne (Maney Publishing, 2015)
    This work aims to show the characterisation of Cr–V–N coatings, with the varied amounts of Cr and V. CrN, VN and Cr–V–N coatings were deposited onto silicon and XC100 steel substrates by reactive radio frequency magnetron ...
  • Friction and Wear Performance of Biomaterials Alloy AISI 316L and Ti-6Al-7Nb 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; LABAIZ, Mohamed; ABDUL SAMAD, Mohammed; ccMONTAGNE, Alex (Society for Biomaterials and Artificial Organs - India, 2016)
    We became interested in this work to study the tribological behavior of two total hip replacements steel AISI 316L and titanium alloy Ti-6Al-7Nb tests performed in this work are essays with reciprocating movement. The ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales