• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Contributions of interfaces on the mechanical behavior of 3D printed continuous fiber reinforced composites

Article dans une revue avec comité de lecture
Auteur
LI, Shixian
557928 School of Traffic and Transportation Engineering
1073080 ICube Laboratory, University of Strasbourg, CNRS, France
WANG, Kui
557928 School of Traffic and Transportation Engineering
ZHU, Wanying
557928 School of Traffic and Transportation Engineering
AHZI, Said
217648 Laboratoire des sciences de l'ingénieur, de l'informatique et de l'imagerie [ICube]
CHINESTA, Francisco
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
564849 ESI Group [ESI Group]

URI
http://hdl.handle.net/10985/22296
DOI
10.1016/j.conbuildmat.2022.127842
Date
2022-07
Journal
Construction and Building Materials

Résumé

3D printing using continuous fiber reinforcement provides a new technical method for preparing complex components with high mechanical behaviors. However, these printed composites have great differences in interfacial behaviors, affecting overall performance. This study aimed to investigate the tensile behaviors of 3D printed continuous fiber filled composites. The structural evolutions and failure features of the composites induced by strain were analyzed with the consideration of interfaces, influenced by the reinforcement fibers, stacking sequences as well as raster orientations. A roller peeling test was conducted to quantify the interfacial strength of different materials. An analytical approach was proposed to predict the stiffness behavior of the printed composites by introducing an interfacial strengthening coefficient into the volume average stiffness model. The predictions of stiffness, for the 3D printed continuous fiber filled composites with different fibers, stacking sequences and raster orientations, were in good agreement with experimental results.

Fichier(s) constituant cette publication

Nom:
PIMM_CBM_2022_CHINESTA.pdf
Taille:
7.331Mo
Format:
PDF
Fin d'embargo:
2023-01-01
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Non-intrusive proper generalized decomposition involving space and parameters: application to the mechanical modeling of 3D woven fabrics 
    Article dans une revue avec comité de lecture
    LEÓN, Angel; MUELLER, SEBASTIEN; DE LUCA, Patrick; SAID, Rajab; DUVAL, Jean Louis; CHINESTA, Francisco (SpringerOpen, 2019)
    In our former works we proposed different Model Order Reduction strategies for alleviating the complexity of computational simulations. In fact we proved that separated representations are specially appealing for addressing ...
  • Modelling of multiple impacts for the prediction of distortions and residual stresses induced by ultrasonic shot peening (USP) 
    Article dans une revue avec comité de lecture
    CHAISE, Thibaut; LI, Jun; NÉLIAS, Daniel; KUBLER, Régis; TAHERI, Said; DOUCHET, Gérard; ROBIN, Vincent; GILLES, Philippe (Elsevier, 2012)
    During a manufacturing process, the ultrasonic shot peening (USP) technique can be used as the final surface treatment. The aim of this operation is to introduce surface compressive residual stresses in order to prevent ...
  • Modelling of multiple impacts for the prediction of distortions and residual stresses induced by ultrasonic shot peening (USP) 
    Article dans une revue avec comité de lecture
    CHAISE, Thibaut; LI, Jun; NELIAS, Daniel; KUBLER, Régis; TAHERI, Said; DOUCHET, Gérard; ROBIN, Vincent; GILLES, Philippe (Elsevier, 2012)
    During a manufacturing process, the ultrasonic shot peening (USP) technique can be used as the final surface treatment. The aim of this operation is to introduce surface compressive residual stresses in order to prevent ...
  • Fuzzy logic based energy management strategy for a fuel cell/battery/ultra-capacitor hybrid ship 
    Communication avec acte
    ZHU, Lisi; PENG, Dongkai; HAN, Jingang; WANG, Tianzhen; TANG, Tianhao; CHARPENTIER, Jean-Frederic (IEEE, 2014)
    In this paper, energy management strategy based on fuzzy logic is proposed for a fuel cell hybrid ship, combining proton exchange membrane fuel cell (PEMFC), battery and ultra-capacitor (UC). This hybrid system aims to ...
  • Isogeometric shape optimization of smoothed petal auxetic structures via computational periodic homogenization 
    Article dans une revue avec comité de lecture
    WANG, Zhen-Pei; POH, Leong Hien; DIRRENBERGER, Justin; ZHU, Yilin; FOREST, Samuel (Elsevier, 2017)
    An important feature that drives the auxetic behaviour of the star-shaped auxetic structures is the hinge-functional connection at the vertex connections. This feature poses a great challenge for manufacturing and may lead ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales