Laboratoire Mechanics, Surfaces and Materials Processing (MSMP): Soumissions récentes

Voici les éléments 57-63 de 420

    • Slinky stator : The impact of manufacturing process on the magnetic properties 
      Communication avec acte
      EL YOUSSEF, Mohamad; VAN GORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; LAVALLEY, Yannick; COUR, Christiane; LECUPPE, Thomas; ccCLENET, Stephane (IEEE, 2017)
      The manufacturing of a slinky stator core is the result of a sequence of difference processes: straightening, punching, rolling….. It has been shown in the literature that manufacturing processes lead to a degradation of ...
    • Intrinsic heat treatment induced graded surficial microstructure and tribological properties of selective laser melted titanium 
      Article dans une revue avec comité de lecture
      KANG, Nan; CAO, Yang; ZHAO, Chunling; ZHAO, Yu; LIN, Chin; CODDET, Christian; ccEL MANSORI, Mohamed; ccCONIGLIO, Nicolas (American Society of Mechanical Engineers, 2021)
      In the course of the selective laser melting (SLM) process, the part is built layer by layer involving partial re-melting/heating of the previous layer, called as intrinsic heat treatment. Therefore, superficial properties ...
    • Experimental set up for magnetomechanical measurements with a closed flux path sample 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; VAN GORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; ccCLENET, Stephane (De Gruyter, 2020)
      In this article, an experimental procedure is presented to handle magnetic measurements under uniaxial tensile stress reaching the plastic domain. The main advantage of the proposed procedure is that it does not require ...
    • The effect of punching on electrical machine 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; BENABOU, AbdelKader; VAN GORP, Adrien; FAVEROLLE, Pierre; MIPO, Jean-Claude; LAVALLEY, Yannick; LECUPPE, Thomas; ccCOOREVITS, Thierry; ccCLENET, Stephane (IOS Press, 2019)
      This work enlightens the impact of punching on a specific stator performances. Two specimens type are withdrawn from a M330A35 punched lamination sheet. One type represents a closed magnetic circuit while the other represents ...
    • Numerical porosimetry: Evaluation and comparison of yield stress fluids method, mercury intrusion porosimetry and pore network modelling approaches 
      Article dans une revue avec comité de lecture
      ccRODRIGUEZ DE CASTRO, Antonio; AGNAOU, Mehrez; ccAHMADI-SENICHAULT, Azita; OMARI, Abdelaziz (Elsevier BV, 2020)
      Mercury Intrusion Porosimetry (MIP) is still today the reference porosimetry technique despite its environmental health and safety concerns. As a safe alternative, the Yield Stress fluids Method (YSM) consists in computing ...
    • Improving global ferromagnetic characteristics of laminations by heterogeneous deformation 
      Article dans une revue avec comité de lecture
      EL YOUSSEF, Mohamad; VANGORP, Adrien; BENABOU, Abdelkader; FAVEROLLE, Pierre; MIPO, Jean-Claude; ccCLENET, Stephane (Institute of Electrical and Electronics Engineers, 2021)
      In this paper, an experimental procedure is presented in order to handle magnetic measurements under uniaxial tensile stress reaching the plastic domain. The main advantage of the proposed procedure is that it does not ...
    • Investigation of subgrains in directionally solidified cast mono-seeded silicon and their interactions with twin boundaries 
      Article dans une revue avec comité de lecture
      BECKER, Maike; PIHAN, Etienne; GUITTONNEAU, Fabrice; REGULA, Gabrielle; OUADDAH, Hadjer; REINHART, Guillaume; MANGELINCK-NOËL, Nathalie; BARRALLIER, Laurent (2020)
      Directional solidification of a cast mono silicon seed and of a float-zone (FZ) silicon seed was performed and the grain and defect structures of the seeds as well as of the regrown parts are analyzed. In situ X-ray ...