• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire de Conception Fabrication Commande (LCFC)
  • View Item
  • Home
  • Laboratoire de Conception Fabrication Commande (LCFC)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Caractérisation de lubrifiant par approche semi – industrielle pour le forgeage de précision

Communication avec acte
Author
MORHAIN, Luc
SECORDEL, Pascal
107452 Laboratoire de Conception Fabrication Commande [LCFC]
ccLANGLOIS, Laurent

URI
http://hdl.handle.net/10985/9235
Date
2007

Abstract

En forgeage de précision, la réussite d’une gamme de déformation dépend en grande partie des performances du lubrifiant utilisé. Celui - ci doit permettre d’éviter un contact direct entre l’acier forgé et l’outil et favoriser l’écoulement du métal dans les outillages. L’étude proposée porte sur la mise en place d’essais de caractérisation de lubrifiants pour le forgeage de précision en conditions semi industrielles. Cette étude repose d’une part sur une démarche d’identification et de maîtrise des paramètres influant sur l’opération de forgeage et d’autre part sur la mise en place d’outillages instrumentés permettant un suivi de certains paramètres de forgeage. L’effet du lubrifiant est évalué suivant des critères liés aux efforts de forgeage et à la géométrie de la pièce forgée. Le protocole expérimental mis en place a permis de mener une étude comparative sur les performances de plusieurs lubrifiants de type polymère et la phosphatation.
 
The success of a cold forging process strongly depends on the effectiveness of the lubricant system. The two main functions of this one is to avoid direct contact between the forged metal and the tools and to help metal flow in the dies. This study presents results obtained with an experimental procedure in order to characterize the lubricant effectiveness during cold forging under semi-industrial conditions. This procedure is based on the identification of the parameters related to the lubricant and driving the forging process. It is based too on the instrumentation of the forging tool in order to follow some particular forging parameters. The effectiveness of the lubricant is estimated through the measurement of the forging load and some dimensions on the forged part. This experimental procedure allowed comparing the effectiveness of two polymer type lubricants and the classical zinc phosphate precoat.
 

Files in this item

Name:
LCFC_CFM_2007_LANGLOIS.pdf
Size:
484.6Kb
Format:
PDF
View/Open

Collections

  • Laboratoire de Conception Fabrication Commande (LCFC)

Related items

Showing items related by title, author, creator and subject.

  • Influence of physical capacities of males with transtibial amputation on gait adjustments on sloped surfaces 
    Article dans une revue avec comité de lecture
    LANGLOIS, Karine; VILLA, Coralie; BONNET, Xavier; LAVASTE, François; FODÉ, Pascale; MARTINET, Noël; ccPILLET, Helene (Rehabilitation Research and Development Service, Department of Veterans Affairs, 2014)
    The aim of the study was to investigate how kinematic and kinetic adjustments between level and slope locomotion of persons with transtibial amputation are related to their individual muscular and functional capacities. A ...
  • Cross-Slope and Level Walking Strategies During Swing in Individuals With Lower Limb Amputation 
    Article dans une revue avec comité de lecture
    VILLA, Coralie; LOIRET, Isabelle; LANGLOIS, Karine; BONNET, Xavier; LAVASTE, François; FODÉ, Pascale; ccPILLET, Helene (Elsevier BV, 2017)
    Objective To quantitatively analyze prosthetic limb swing phase gait strategies used to adapt to cross slopes compared with flat surfaces. Design Cross-sectional study. Setting Gait laboratory. Participants A volunteer ...
  • Influence of Mechanical Surface Treatment on High-Temperature Oxidation of Pure Titanium 
    Article dans une revue avec comité de lecture
    KANJER, Armand; OPTASANU, Virgil; LAVISSE, Luc; MARCO DE LUCAS, Maria Del Carmen; DEJARDIN, Steeve; FRANÇOIS, Manuel; BERGER, Pascal D.; PEYRE, Patrice; GORNY, Cyril; MONTÉSIN, Tony (Springer Verlag, 2017)
    The excellent combination of light-weight and good mechanical properties makes titanium alloys attractive for compressor section components in gas turbine engines (temperature between 250 and 600 °C). However, above 600 ...
  • Influence of Mechanical Surface Treatment on High-Temperature Oxidation of Pure Titanium 
    Article dans une revue avec comité de lecture
    KANJER, Armand; OPTASANU, Virgil; LAVISSE, Luc; MARCO DE LUCAS, María Del Carmen; DEJARDIN, Steeve; FRANÇOIS, Manuel; BERGER, Pascal; PEYRE, Patrice; GORNY, Cyril; MONTÉSIN, Tony (Springer Verlag, 2017)
    The excellent combination of light-weight and good mechanical properties makes titanium alloys attractive for compressor section components in gas turbine engines (temperature between 250 and 600 °C). However, above 600 ...
  • Numerical investigation of the influence of defects on the multiaxial fatigue strength of additively manufactured alloys 
    Article dans une revue avec comité de lecture
    PENKULINTI, Sai Sreeniva; ccBONNERIC, Matthieu; ccSAINTIER, Nicolas; ccVERQUIN, Benoit; ccLEFEBVRE, Fabien; ccPALIN-LUC, Thierry; GHYS, Pascal (Elsevier, 2024)
    Laser Powder Bed Fusion (L-PBF) is one of the Additive Manufacturing (AM) techniques that have revealed salient advantages in enabling the fabrication of 3D parts with intricate shapes and added functionalities. Despite ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales