Earthen construction: an increase of the mechanical strength by optimizing the dispersion of the binder phase
TypeArticles dans des revues avec comité de lecture
Although of interest for its low embodied energy content for construction, earth is usually not used for modern construction due to the expensive, artisanal and complicated process and the high variability of the raw material. The transfer of techniques dedicated to cement concrete could help the industrialization of this material. The use of dispersant for an improved dispersion of the earth powder has been investigated for both dispersion of earth fine fraction and water (here named the binding phase) and mortar made with calibrated sand. An improvement of the rheology is observed with lower viscosity and yield stress. This leads to a very small improvement of the density however concomitant with a marked increase of the mechanical properties, Young modulus and compressive strength. The analysis of the microstructure of the mortar shows an increase of the largest pores, and a decrease of the clay platelets flocs. The evolutions of these properties are analyzed in terms of the Rumpf model at two different scales. The dispersant mainly acts on the platelet arrangement that defines the forces between particles, but also simultaneously decreases the permeability of this binding phase, therefore entrapping more air during the mixing of the powder and water. Clearly the use of a dispersant may be of interest for the processing of earth material on liquid state, decreasing the viscosity and/or allowing the reduction of the water content, and finally improving strength.
Fichier(s) constituant cette publication
Cette publication figure dans le(s) laboratoire(s) suivant(s)
Visualiser des documents liés par titre, auteur, créateur et sujet.
Observation of the shock wave propagation induced by a high-power laser irradiation into an epoxy material ESCAULT, Romain; BERTHE, Laurent; BOUSTIE, Michel; TOUCHARD, Fabienne; LESCOUTE, Emilien; SOLLIER, Arnaud; MERCIER, Patrick; BERNIER, Jacky (IOP PUBLISHING, 2014)The propagation of laser-induced shock waves in a transparent epoxy sample is investigated by optical shadowgraphy. The shock waves are generated by a focused laser (3 ns pulse duration—1.2 to 3.4TWcm−2) producing pressure ...
Experimental and numerical investigations of shock and shear wave propagation induced by femtosecond laser irradiation in epoxy resins ECAULT, Romain; BERTHE, Laurent; TOUCHARD, Fabienne; BOUSTIE, Michel; LESCOUTE, Emilien; SOLLIER, Arnaud; VOILLAUME, Hubert (IOP Publishing Ltd, 2015)In this work, original shock experiments are presented. Laser-induced shock and shear wave propagations have been observed in an epoxy resin, in the case of femtosecond laser irradiation. A specific time-resolved shadowgraphy ...
Semi-automated stereoradiographic upper limb 3D reconstructions using a combined parametric and statistical model: a preliminary study LEBAILLY, Fréderic; LIMA, Lucas; CLAIREMIDI, Alain; AUBERT, Benjamin; GUERARD, Sandra; CHAÏBI, Yasmina; DE GUISE, Jacques; FONTAINE, Christian; SKALLI, Wafa (springer, 2012)PURPOSE: Quantitative assessment of 3D clinical indices may be crucial for elbow surgery planning. 3D parametric modeling from bi-planar radiographs was successfully proposed for spine and lower limb clinical investigation ...
PIQUARD, Romain; GILBIN, Alexandre; D'ACUNTO, Alain; FONTAINE, Michaël; DUDZINSKI, Daniel; THIBAUD, Sébastien (Institut Français de Mécanique Avancée, 2014)Cet article présente des essais de micro-coupe orthogonale et oblique à partir de tournage sur un acier 40NiCrMo16. Les résultats obtenus démontrent l’influence du rayon d’acuité d’arête sur les efforts mesurés notamment ...
PIQUARD, Romain; GILBIN, Alexandre; FONTAINE, Michaël; D'ACUNTO, Alain; THIBAUD, Sébastien; DUDZINSKI, Daniel (Czech Machine Tool Society, 2014)In order to model micro-milling cutting forces, a way is to apply a local model on discretized elements of the cutting edge and then summing on the whole edge to obtain the global cutting forces. This local model is usually ...