Role of machining defects and residual stress on the AISI 304 fatigue crack nucleation
Article dans une revue avec comité de lecture
Machining defects as rebuilt material and dislodgement were often induced by cutting of difficult to machining AISI 304 stainless steel. Their density increases with a decreasing of cutting speed. The effect of these defects on surface topography and residual stress was evaluated by roughness and X-ray diffraction measurements coupled with numerical simulation. The role of the rebuilt material on the distribution of fatigue crack nucleation sites was investigated by scanning electron microscope examination of post fatigue samples loaded at different imposed strain amplitudes. The association of machining defects and fatigue crack nucleation sites was attributed to the contribution of additional tensile residual stresses induced by rebuilt material rather than local stress concentration. Moreover, the fatigue crack coalescence is promoted by increasing the rebuilt material density. When the machining defect density increases from 5 to 60 particles/mm2, the fatigue life decreases from -22% to -65% with respect to the electropolished surface. © 2014 Wiley Publishing Ltd.
Fichier(s) constituant cette publication
Cette publication figure dans le(s) laboratoire(s) suivant(s)
Visualiser des documents liés par titre, auteur, créateur et sujet.
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation Article dans une revue avec comité de lectureSIDHOM, Naziha; BEN MOUSSA, Naoufel; JANEB, Sameh; BRAHAM, Chedly; SIDHOM, Habib (Elsevier, 2014)The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated. Surface texture, work-hardening and residual ...
Numerical and experimental analysis of residual stress and plastic strain distributions in machined stainless steel Article dans une revue avec comité de lectureBEN MOUSSA, Naoufel; SIDHOM, Habib; BRAHAM, Chedly (Elsevier, 2012)In this study, a numerical approach has been developed to predict the near surface residual stresses and plastic strain resulting from turning in orthogonal cutting configuration. This approach is based on the Arbitrary ...
Effect of machining processes on the residual stress distribution heterogeneities and their consequences on the stress corrosion cracking resistance of AISI 316L SS in chloride medium Article dans une revue avec comité de lectureRHOUMA, Amir Ben; SIDHOM, Naziha; MAKHLOUF, Kamel; SIDHOM, Habib; BRAHAM, Chedly; GONZÁLEZ, Gonzalo (Springer Verlag, 2019)The effects of machining such as grinding and turning on the microstructural and mechanical changes of the machined surfaces of AISI 316L stainless steel (SS) have been studied. Surface aspects and surface defects have ...
Effects of finishing processes on the fatigue life improvements of electro-machined surfaces of tool steel Article dans une revue avec comité de lectureGHANEM, Farhat; FREDJ, Nabil Ben; SIDHOM, Habib; BRAHAM, Chedly (Springer Verlag, 2011)Machining the EN X160CrMoV12 tool steel by electro-discharge machining (EDM) process generates significant modifications of microgeometrical, microstructural and mechanical properties of the upper layers of the machined ...
Correlation between microstructure and intergranular corrosion behavior of low delta-ferrite content AISI 316L aged in the range 550e700 C Article dans une revue avec comité de lectureBEN RHOUMA, A; AMADOU, Tidiane; SIDHOM, Habib; BRAHAM, Chedly (Elsevier, 2017)The microstructure and the phase identification of austenitic stainless steel AISI 316L with low δ-ferrite content (δ ≤ 1%) and aged for up to 80 000 h at temperatures ranging from 550 to 700 °C were investigated by using ...