SAM: Soumissions récentes

Voici les éléments 2090-2096 de 6547

    • G-DfAM: a methodological proposal of generative design for additive manufacturing in the automotive industry 
      Article dans une revue avec comité de lecture
      BRIARD, Tristan; ZAMARIOLA, Nicolo; ccSEGONDS, Frederic (Springer Verlag, 2020)
      Metal additive manufacturing is an emerging technology in the industry and has a great potential. Moreover, new technologies like generative design can maximize this potential by computing complex optimized parts for ...
    • Robustness and Reproducibility of a Glenoid-Centered Scapular Coordinate System Derived From Low-Dose Stereoradiography Analysis 
      Article dans une revue avec comité de lecture
      OHL, Xavier; LAGACÉ, Pierre-Yves; BILLUART, Fabien; GAGEY, Olivier; ccSKALLI, Wafa; HAGEMEISTER, Nicola (Human Kinetics, 2015)
      A robust and reproducible scapular coordinate system is necessary to study scapulo-thoracic kinematics. The coordinate system recommended by the ISB (International Society of Biomechanics) is difficult to apply in studies ...
    • Elastic-strain distribution in metallic film-polymer substrate composites 
      Article dans une revue avec comité de lecture
      GEANDIER, Guillaume; RENAULT, Pierre Olivier; LE BOURHIS, Éric; GOUDEAU, Philippe H.; FAURIE, Damien; LE BOURLOT, Christophe; DJ́MIA, Ph; CASTELNAU, Olivier; CH́RIF, S. M. (American Institute of Physics, 2010)
      Synchrotron x-ray radiation was used for in situ strain measurements during uniaxial tests on polymer substrates coated by a metallic gold film 400 nm thick deposited without interlayer or surface treatment. X-ray diffraction ...
    • Economic models used in consequential life cycle assessment: a literature review 
      Article dans une revue avec comité de lecture
      ALMEIDA, Denise T.L.; ccCHARBUILLET, Carole; HESLOUIN, Charlotte; LEBERT, Alexandra; ccPERRY, Nicolas (ELSEVIER, 2020)
      The construction sector is a key actor for achieving the sustainable development goals, particularly from an environmental point of view, due to the significant sector's contribution to energy consumption, greenhouse gas ...
    • Radars in Transport Applications 
      Chapitre d'ouvrage scientifique
      IBÁÑEZ PINILLO, Rubén; ccCHINESTA SORIA, Francisco; ccABISSET-CHAVANNE, Emmanuelle; ABENIUS, Erik; HUERTA, Antonio (Springer, 2020)
      In the recent years, automotive car industry is evolving towards a new generation of autonomous vehicles, where decision making is not fully perform by the driver but it partially relies on the technology of the car itself. ...
    • Non-Intrusive In-Plane-Out-of-Plane Separated Representation in 3D Parametric Elastodynamics 
      Article dans une revue avec comité de lecture
      GERMOSO, Claudia; QUARANTA, Giacomo; DUVAL, Jean Louis; ccCHINESTA SORIA, Francisco (MDPI, 2020)
      Mesh-based solution of 3D models defined in plate or shell domains remains a challenging issue nowadays due to the fact that the needed meshes generally involve too many degrees of freedom. When the considered problem ...
    • Influence of thermal history on the mechanical properties of poly(ether ketone ketone) copolymers 
      Article dans une revue avec comité de lecture
      DEBERTRAND, Louis; PARIS, Christophe; CINQUIN, Jacques; BRULÉ, Benoît; ccREGNIER, Gilles; ccFAYOLLE, Bruno (Wiley, 2019)
      Since poly(ether ketone ketone) (PEKK) is a good candidate as a matrix for composite structural parts, the mechanical properties of PEKK copolymers prepared from diphenyl ether, terephthalic acid (T), and isophthalic acid ...