SAM: Soumissions récentes

Voici les éléments 2433-2439 de 6448

    • HESAM: A Human cEntered Sustainable Additive Manufacturing Tool for Early Design Stages 
      Article dans une revue avec comité de lecture
      ROCHETON, Bastien; ccSEGONDS, Frederic; LAVERNE, Floriane; ccPERRY, Nicolas (CAD Solutions LLC (imprimé) and Taylor & Francis Online (en ligne), 2021)
      Despite its development over the past several years, Additive Manufacturing (AM) has not yet unveiled its full potential for sustainable manufacturing. The recent awareness of the environmental impact of products we consume ...
    • Application of an experimental design to study AISI 4340 and 300M steels electropolishing in a concentrated perchloric/acetic acid solution 
      Article dans une revue avec comité de lecture
      ROSCOL, V; DUBENT, Sébastien; BENSALAH, W; MIERZEJEWSKI, S; OTTENIO, R; DEPETRIS-WERY, M; AYEDI, H F (IOP Science, 2020)
      The objective of this study was to assess AISI 4340 and 300 M steels electropolishing performance in aconcentrated perchloric/acetic acid electrolyte. The statistical analysis on a two-level fractional design(FFD)24-1was ...
    • Influence of process parameters on thermal and mechanical properties of polylactic acid fabricated by fused filament fabrication 
      Article dans une revue avec comité de lecture
      VANAEI, Hamid Reza; ccSHIRINBAYAN, Mohammadali; ccDELIGANT, Michael; RAISSI, Kaddour; ccFITOUSSI, Joseph; ccKHELLADI, Sofiane; ccTCHARKHTCHI, Abbas (Wiley-Blackwell, 2020)
      Fused filament fabrication is considered one of the most used processes in additive manufacturing rapid prototypes out of polymeric material. Poor strength of the deposited layers is still one of the main critical problems ...
    • Humid Ageing of Organic Matrix Composites 
      Chapitre d'ouvrage scientifique
      VERDU, Jacques; ccCOLIN, Xavier (Springer, 2014)
      In this chapter, several aspects of the ageing phenomena induced by water in organic matrix composites are examined, essentially from the physico-chemical point of view. It is first important to recognize that there are ...
    • Nano- and Micromechanics of Crystalline Polymers 
      Chapitre d'ouvrage scientifique
      GALESKI, Andrzej; ccREGNIER, Gilles (Hanser Fachbuchverlag, 2009)
      It is currently thought that crystalline polymers consists of lamellar crystals which are separated from each other by a layer of amorphous polymer and are held together by tie molecules through the amorphous phase [e.g. ...
    • Dense-gas effects on compressible boundary-layer stability 
      Article dans une revue avec comité de lecture
      CINNELLA, Paola; GRASSO, Francesco; ccROBINET, Jean-Christophe; ccSCIACOVELLI, Luca; ccGLOERFELT, Xavier (Cambridge University Press (CUP), 2020)
      A study of dense-gas effects on the stability of compressible boundary-layer flows is conducted. From the laminar similarity solution, the temperature variations are small due to the high specific heat of dense gases, ...
    • Influence of scope definition in recycling rate calculation for European e-waste extended producer responsibility 
      Article dans une revue avec comité de lecture
      HORTA ARDUIN, Rachel; GRIMAUD, Guilhem; MARTINEZ LEAL, Jorge; POMPIDOU, Stéphane; ccCHARBUILLET, Carole; ccLARATTE, Bertrand; ccALIX, Thecle; ccPERRY, Nicolas (Elsevier, 2019)
      Efficiency indicators have been frequently used to assess end-of-life chain performance, mostly. In terms of the percentage of mass sent to re-use, recycling, and/or energy recovery facilities. While legislation gives a ...