SAM: Soumissions récentes

Voici les éléments 3850-3856 de 6547

    • A methodological proposal to link Design with Additive Manufacturing to environmental considerations in the Early Design Stages 
      Article dans une revue avec comité de lecture
      MARKOU, Foteini; ccSEGONDS, Frederic; RIO, Maud; ccPERRY, Nicolas (Springer Verlag, 2017)
      Additive manufacturing is an innovative manufacturing process that enables rapid manufacturing of functional products and parts. On the other side, considering environmental aspects in design is beneficial as it leads to ...
    • Dual-Multiphase Motor Drives for Fault- Tolerant Applications: Power Electronic Structures and Control Strategies 
      Article dans une revue avec comité de lecture
      DOS SANTOS MORAES, Tiago José; MEINGUET, Fabien; GUERIN, Mael; ccSEMAIL, Eric; ccNGUYEN, Ngac Ky (Institute of Electrical and Electronics Engineers, 2017)
      This paper analyzes two fault-tolerant dualmultiphase motor drives, a series connected topology and a standard H-bridge topology. Previous studies have shown that the series connected topology is appropriate to an aerospace ...
    • Advances in material and friction data for modelling of metal machining 
      Article dans une revue avec comité de lecture
      MELKOTE, Shreyes; GRZESIK, Wit; ccMARTINS DO OUTEIRO, Jose Carlos; RECH, Joël; SCHULZE, Volker; ATTIA, Helmi; ARRAZOLA, Pedro José; M'SAOUBI, Rachid; SALDANA, Christopher (Elsevier, 2017)
      This paper reviews recent advances in constitutive and friction data and models for simulation of metal machining. Phenomenological and physically-based constitutive models commonly used in machining simulations are presented ...
    • Mechanical characterization of a prototype a-C:Cr,Si and its tribological behavior at high temperature 
      Article dans une revue avec comité de lecture
      STAIA, Mariana; DUBAR, Laurent; DUBAR, Mirentxu; PUCHI-CABRERA, Eli-Saul; IOST, Alain; DE BAETS, Patrick; DUBOIS, André (Elsevier, 2016)
      The results of the mechanical and tribological characterization of a prototype a-C:Cr, Si sputtered coating are presented. The hardness and the elastic modulus of the coated system have been determined by means of ...
    • Experimental and theoretical study of iron and mild steel combustion in oxygen flows 
      Article dans une revue sans comité de lecture
      EL-RABII, Hazem; KAZAKOV, Kirill A.; MULLER, Maryse (American Institute of Physics, 2017)
      The effects of oxygen flow speed and pressure on the iron and mild steel combustion are investigated experimentally and theoretically. The studied specimens are vertical cylindrical rods subjected to an axial oxygen flow ...
    • Laser offset welding of AZ31B magnesium alloy to 316 stainless steelG 
      Article dans une revue avec comité de lecture
      CASALINO, Giuseppe; GUGLIELMI, P; LORUSSO, V.D.; MORTELLO, Michelangelo; SORGENTE, D; PEYRE, Patrice (Elsevier, 2017)
      In this paper, the feasibility of using a fiber laser to perform a dissimilar metal joining was explored. AZ31B magnesium and 316 stainless steel were autogenously joined in butt configuration. The weldability between ...
    • Correlation of the high and very high cycle fatigue response of ferrite based steels with strain rate-temperature conditions 
      Article dans une revue avec comité de lecture
      TORABIAN, Noushin; DIRRENBERGER, Justin; ADAMSKI, Frédéric; ZIAEI-RAD, Saeed; ccRANC, Nicolas; ccFAVIER, Véronique (Elsevier, 2017)
      The discrepancies observed between conventional and ultrasonic fatigue testing are assessed through the mechanisms of dislocation mobility in BCC metals. The existence of a transition condition between thermally-activated ...