• 

  Liquid Transfer for Viscoelastic Solutions 

  Article dans une revue avec comité de lecture

  PINGULKAR, Hrishikesh; PEIXINHO, Jorge; CRUMEYROLLE, Olivier (American Chemical Society (ACS), 2021-08-18)

  Viscoelastic liquid transfer from one surface to another is a process that finds applications in many technologies, primarily in printing. Here, cylindrical-shaped capillary bridges pinned between two parallel disks are ...
• 

  Determination of the pressure in micrometric bubbles in irradiated nuclear fuels 

  Article dans une revue avec comité de lecture

  DOWEK, Rébecca; CAGNA, Céline; NOIROT, Jean; ZACHARIE-AUBRUN, Isabelle; BLAY, Thierry; HANIFI, Karine; BIENVENU, Philippe; ROURE, Ingrid; CABIÉ, Martiane; DUMONT, Myriam (Elsevier BV, 2021)

  In oxide nuclear fuels, at high burn-up or during high temperature periods such as ramp tests, out-of- pile heating tests, or any irradiations at high linear heat rates, fission gases can form micrometric or quasi-micrometric ...
• 

  Multi-scale analysis of mechanical properties and damage behavior of polypropylene composite (GF50-PP) plate at room and cryogenic temperatures 

  Article dans une revue avec comité de lecture

  SHIRINBAYAN, Mohammadali; REZAEI-KHAMSEH, Mojdeh; NIKOOHARF, Mohammad Hossein; TCHARKHTCHI, Abbas (Elsevier BV, 2021)

  In this paper, glass fiber-reinforced polypropylene (GF50-PP) composite composed of long fibers was prepared by the thermo-compression process for the very first time. This composite presents high mechanical strength and ...
• 

  An Investigation to Study the Effect of Process Parameters on the Strength and Fatigue Behavior of 3D-Printed PLA-Graphene 

  Article dans une revue avec comité de lecture

  EL MAGRI, Anouar; VANAEI, Saeedeh; SHIRINBAYAN, Mohammadali; VAUDREUIL, Sébastien; TCHARKHTCHI, Abbas (MDPI, 2021)

  3D printing, an additive manufacturing process, draws particular attention due to its ability to produce components directly from a 3D model; however, the mechanical properties of the produced pieces are limited. In this ...
• 

  Study of Concentrated Short Fiber Suspensions in Flows, Using Topological Data Analysis 

  Article dans une revue avec comité de lecture

  MEZHER, Rabih; ARAYRO, Jack; HASCOET, Nicolas; CHINESTA, Francisco (MDPI, 2021)

  The present study addresses the discrete simulation of the flow of concentrated suspensions encountered in the forming processes involving reinforced polymers, and more particularly the statistical characterization and ...
• 

  A Modified DLS Scheme With Controlled Cyclic Solution for Inverse Kinematics in Redundant Robots 

  Article dans une revue avec comité de lecture

  SAFEEA; BEAREE, Richard; NETO, Pedro (Institute of Electrical and Electronics Engineers (IEEE), 2021)

  Redundancy in robotic manipulators has many advantages. It is successfully used to achieve better dexterity, and to avoid obstacles, singularities, or the kinematic limitations. However, redundancy makes the inverse ...
• 

  Impact of avatar facial anthropomorphism on body ownership, attractiveness and social presence in collaborative tasks in immersive virtual environments 

  Article dans une revue avec comité de lecture

  DUBOSC, Charlotte; GORISSE, Geoffrey; CHRISTMANN, Olivier; FLEURY, Sylvain; POINSOT, Killian; RICHIR, Simon (Elsevier BV, 2021)

  Effective collaboration in immersive virtual environments requires to be able to communicate flawlessly using both verbal and non-verbal communication. We present two experiments investigating the impact of facial ...

Voir plus