• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • View Item
  • Home
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental Investigation of the Effect of Burnishing Force on Service Properties of AISI 1010 Steel Plates

Article dans une revue avec comité de lecture
Author
GHARBI, Fathi
163133 Institut Supérieur des Sciences Appliquées et de Technologie de Kairouan [Kairouan] [ISSAT Kairouan]
SGHAIER, Salem
BENAMEUR, Tarek
ccMOREL, Franck
206863 Laboratoire des Arts et Métiers ParisTech d'Angers - Procédés Matériaux Durabilité [LAMPA - PMD]

URI
http://hdl.handle.net/10985/10263
DOI
10.1007/s11665-014-1349-1
Date
2014
Journal
Journal of Materials Engineering and Performance

Abstract

This paper presents the results obtained with a new ball burnishing tool developed for the mechanical treatment of large flat surfaces. Several parameters can affect the mechanical behavior and fatigue of workpiece. Our study focused on the effect of the burnishing force on the surface quality and on the service properties (mechanical behavior, fatigue) of AISI 1010 steel hot-rolled plates. Experimental results assert that burnishing force not exceeding 300 N causes an increase in the ductility. In addition, results indicated that the effect of the burnishing force on the residual surface stress was greater in the direction of advance than in the cross-feed direction. Furthermore, the flat burnishing surfaces did not improve the fatigue strength of AISI 1010 steel flat specimens.

Files in this item

Name:
LAMPA_JMEP_MOREL_2014.pdf
Size:
2.492Mb
Format:
PDF
View/Open

Collections

  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)

Related items

Showing items related by title, author, creator and subject.

  • Correlation between microstructure and cyclic behavior of 316L stainless steel obtained by Laser Powder Bed Fusion 
    Article dans une revue avec comité de lecture
    LIANG, Xiaoyu; HOR, Anis; ROBERT, Camille; SALEM, Mehdi; ccMOREL, Franck (Wiley, 2022-02-23)
    In this work, stainless steel 316L obtained by Laser Powder Bed Fusion (L-PBF) has been produced and characterized. The experimental campaign focuses on the samples in the as-built state under cyclic tension-compression ...
  • High cycle fatigue behavior of 316L steel fabricated by laser powder bed fusion: Effects of surface defect and loading mode 
    Article dans une revue avec comité de lecture
    LIANG, Xiaoyu; HOR, Anis; ccROBERT, Camille; SALEM, Mehdi; LIN, Feng; ccMOREL, Franck (Elsevier BV, 2022-03-08)
    The mechanical performances of additive manufactured (AM) material are highly dependent on the fabrication process which inevitably results in surface imperfection as well as porosity. In the present study, the high cycle ...
  • Influence of high pressure coolant assistance on the machinability of the titanium alloy Ti555-3 
    Article dans une revue avec comité de lecture
    BRAHAM-BOUCHNAK, Tarek; ccGERMAIN, Guénaël; MOREL, Anne; FURET, Benoit (Taylor & Francis, 2015)
    The origin of this article is the quantification of productivity gains and the improvement in surface integrity seen for a recent titanium alloy that is seeing increasing use in the aeronautical industry. The Ti555–3 ...
  • Identification de lois de comportement représentatives des conditions d’usinage pour des alliages de titane à différentes teneurs alpha/beta 
    Communication avec acte
    ccGERMAIN, Guénaël; ccAYED, Yessine; BRAHAM-BOUCHNAK, Tarek; MOREL, Anne (Congrès Français de Mécanique, 2013)
    Determining a material constitutive law which is representative of the extreme conditions found in the cutting zone during machining operations is a very challenging problem. In this study, dynamic shear tests, which ...
  • Identification of material constitutive laws representative of machining conditions for two titanium alloys: Ti6Al4V and Ti555-3 
    Article dans une revue avec comité de lecture
    ccGERMAIN, Guenael; MOREL, Anne; BRAHAM-BOUCHNAK, Tarek (American Society of Mechanical Engineers, 2013)
    Determining a material constitutive law that is representative of the extreme conditions found in the cutting zone during machining operations is a very challenging problem. In this study, dynamic shear tests, which ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales