• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • View Item
  • Home
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Study of the mechanical behavior and corrosion resistance of hydroxyapatite sol–gel thin coatings on 316 L stainless steel pre-coated with titania film

Article dans une revue avec comité de lecture
Author
SIDANE, Djahida
CHICOT, Didier
1252 Laboratoire de Mécanique de Lille - FRE 3723 [LML]
YALA, Sabeha
ZIANI, Salima
KHIREDDINE, Hafit
IOST, Alain
211915 Mechanics surfaces and materials processing [MSMP]
DECOOPMAN, Xavier
1252 Laboratoire de Mécanique de Lille - FRE 3723 [LML]

URI
http://hdl.handle.net/10985/10273
DOI
10.1016/j.tsf.2015.09.037
Date
2015
Journal
Thin Solid Films

Abstract

In order to reinforce the clinical applications of hydroxyapatite (HAP) sol–gel coatings deposited onto 316 L stainless steel, we suggest the introduction of an intermediate thin layer of titania (TiO2) on the substrate. The titania sub-layer is introduced in order to improve both the corrosion resistance and the mechanical properties of the HAP/316 L stainless steel coated system. The twocoatings, HAP and TiO2,were studied separately and afterwards, compared with the bi-layered coating. A film without any cracks is obtained under the optimum conditions in terms of annealing temperature, dipping rate and aging effect. Microstructural, morphological and profilometry analysis revealed the non-stoichiometric carbonated porous nature of the hydroxyapatite coatings, which were obtained after annealing at 500 °C during 60 min in the atmosphere. The obtained TiO2 coatings exhibit a dense and uniform surface. Addition of TiO2 as sub-layer of the HAP coating tends to increase the homogeneity and the crystallinity rate as compared to the HAP one. The mechanical properties, i.e. hardness and elastic modulus, are determined by means of nanoindentation experiments and the adhesion between the coating and substrate is estimated by scratch tests. The corrosion behavior is evaluated by potentiodynamic cyclic voltammetry tests. As a main result, the values of the elastic modulus and hardness, respectively of 30 GPa and 2.5 GPa, are relatively high for the HAP–TiO2 bilayer coating. This result allows the use of such coated material as a replacement material for hard tissues. The adhesion strength increased from 2925 mN up to 6430 mN after the addition of the TiO2 intermediate film. According to the Tafel's analysis, the 316 L stainless steel specimens coated with both HAP and titania layers (ECorr = −234 mV, lCorr = 0.089 μA cm−2) present a better resistance than the HAP-coated specimens (ECorr= −460 mV, lCorr=0.860 μA cm−2).

Files in this item

Name:
MSMP_TSF_2015_IOST.pdf
Size:
3.377Mb
Format:
PDF
View/Open

Collections

  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)

Related items

Showing items related by title, author, creator and subject.

  • Propriétés mécaniques par indentation d’un film mince nanometrique de nitrure d’aluminium 
    Article dans une revue avec comité de lecture
    ROUDET, Francine; CHICOT, Didier; DECOOPMAN, Xavier; IOST, Alain; BÜRGI, Juan; MOLLEJA, Javier Garcia; FEUGEAS, Jorge (EDP Sciences, 2015)
    Les propriétés mécaniques des films minces sont généralement déterminées par nanoindentation pour éviter l’influence du substrat. En effet, nous savons que le substrat influence cette mesure dès lors que l’indenteur pénètre ...
  • Analysis of indentation size effect in copper and its alloys 
    Article dans une revue avec comité de lecture
    CHICOT, Didier; PUCHI-CABRERA, Eli-Saul; IOST, Alain; STAIA, M.H; DECOOPMAN, Xavier; ROUDET, F.; LOUIS, G. (Maney Publishing, 2013)
    For describing the indentation size effect (ISE), numerous models, which relate the load or hardness to the indent dimensions, have been proposed. Unfortunately, it is still difficult to associate the different parameters ...
  • Fatigue behavior of a structural steel coated with a WC–10Co–4Cr/Colmonoy 88 deposit by HVOF thermal spraying 
    Article dans une revue avec comité de lecture
    LA BARBERA-SOSA, J.G.; SANTANA, Y.Y.; VILLALOBOS-GUTIERREZ, C.; CHICOT, Didier; LESAGE, J.; DECOOPMAN, Xavier; IOST, Alain; STAIA, M.H.; PUCHI-CABRERA, Eli-Saul (Elsevier, 2013)
    The fatigue behavior of a SAE 4340 steel, coated with a 50% WC–10Co–4Cr/50% Colmonoy 88 deposit, by high velocity oxygen fuel (HVOF) thermal spray, has been investigated. The change in the maximum alternating stress with ...
  • Sliding Wear Response of Nanostructured YSZ Suspension Plasma-Sprayed Coating 
    Article dans une revue avec comité de lecture
    KOSSMAN, Stephania; CHICOT, Didier; DECOOPMAN, Xavier; IOST, Alain; VAN GORP, Adrien; MEILLOT, E.; PUCHI-CABRERA, Eli-Saul; SANTANA, Y.Y.; STAIA, Mariana (ASM International/Springer, 2014)
    Nanostructured yttria-stabilized zirconia coatings for applications in high-temperature environments can be deposited by suspension plasma spraying (SPS) techniques. The present research has been conducted in order to study ...
  • An analysis of the elastic properties of a porous aluminium oxide film by means of indentation techniques 
    Article dans une revue avec comité de lecture
    HEMMOUCHE, L.; CHICOT, Didier; AMROUCHE, A.; IOST, Alain; BELOUCHRANI, M.A.; DECOOPMAN, Xavier; LOUIS, G.; PUCHI-CABRERA, Eli-Saul (Elsevier, 2013)
    The elastic modulus of thin films can be directly determined by instrumented indentation when the indenter penetration does not exceed a fraction of the film thickness, depending on the mechanical properties of both film and ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales