• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Confinement effect in PC/MXD6 multilayer films: Impact of the microlayered structure on water and gas barrier properties

Article dans une revue avec comité de lecture
Auteur
MESSIN, Tiphaine
141328 Polymères Biopolymères Surfaces [PBS]
FOLLAIN, Nadège
141328 Polymères Biopolymères Surfaces [PBS]
GUINAULT, Alain
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
MIQUELARD-GARNIER, Guillaume
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
SOLLOGOUB, Cyrille
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
DELPOUVE, Nicolas
300318 Université de Rouen Normandie [UNIROUEN]
GAUCHER, Valérie
174496 Unité Matériaux et Transformations - UMR 8207 [UMET]
MARAIS, Stéphane
141328 Polymères Biopolymères Surfaces [PBS]

URI
http://hdl.handle.net/10985/11596
DOI
10.1016/j.memsci.2016.10.039
Date
2017
Journal
Journal of Membrane Science

Résumé

The transport properties were specifically investigated from water and gas permeation kinetics, and the corresponding permeation parameters were determined. The confinement effect of MXD6 in the multilayer structure was highlighted by comparing the permeability predicted from the series model equation with the experimental data. Although the MXD6 layers were not homogeneous and continuous for all membranes, water and gas permeabilities of the PC/MXD6 multilayer film were largely reduced. Such improvement of barrier properties was related to the change of the MXD6 structure, considering that the confinement of the MXD6 layers induced by PC layers allowed to bring chain orientation and to reduce the chain segment mobility in the MXD6 amorphous constrained zones. In addition, in the case of a PC/MXD6 multilayer structure well defined with continuous layers and relatively homogeneous thicknesses, the degree of crystallinity was slightly increased.

Fichier(s) constituant cette publication

Nom:
PIMM - JMS - MESSIN - 2017.pdf
Taille:
1.197Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Impact of water and thermal induced crystallizations in a PC/MXD6 multilayer film on barrier properties 
    Article dans une revue avec comité de lecture
    MESSIN, Tiphaine; MARAIS, Stéphane; FOLLAIN, Nadège; CHAPPEY, Corinne; GUINAULT, Alain; MIQUELARD-GARNIER, Guillaume; DELPOUVE, Nicolas; GAUCHER, Valérie; SOLLOGOUB, Cyrille (Elsevier, 2019)
    A multilayer film composed of alternating layers of polycarbonate (PC) and poly(m-xylene adipamide) (MXD6) was elaborated by using an innovative multilayer coextrusion process. Quasi-continuous thin MXD6 layers (nanolayers) ...
  • Structure and Barrier Properties of Multinanolayered Biodegradable PLA/PBSA Films: Confinement Effect via Forced Assembly Coextrusion 
    Article dans une revue avec comité de lecture
    FOLLAIN, Nadège; GUINAULT, Alain; SOLLOGOUB, Cyrille; GAUCHER, Valérie; DELPOUVE, Nicolas; MARAIS, Stéphane; MESSIN, Tiphaine (Washington, D.C. : American Chemical Society, 2017)
    Multilayer coextrusion processing was applied to produce 2049-layer film of poly(butylene succinate-co-butylene adipate) (PBSA) confined against poly(lactic acid) (PLA) using forced assembly, where the PBSA layer thickness ...
  • Biodegradable PLA/PBS multinanolayer membrane with enhanced barrier performances 
    Article dans une revue avec comité de lecture
    MESSIN, Tiphaine; MARAIS, Stéphane; FOLLAIN, Nadège; GUINAULT, Alain; GAUCHER, Valérie; DELPOUVE, Nicolas; SOLLOGOUB, Cyrille (Elsevier, 2020)
    Polyester multilayer membranes with more than 2000 alternating layers of poly(lactic acid) (PLA) and poly(butylene succinate) (PBS) were successfully prepared via a nanolayer coextrusion process equipped with a multiplying-element ...
  • Structural and Barrier Properties of Compatibilized PE/PA6 Multinanolayer Films 
    Article dans une revue avec comité de lecture
    LOZAY, Quentin; BEUGUEL, Quentin; FOLLAIN, Nadège; LEBRUN, Laurent; GUINAULT, Alain; MIQUELARD-GARNIER, Guillaume; TENCÉ-GIRAULT, Sylvie; SOLLOGOUB, Cyrille; DARGENT, Eric; MARAIS, Stéphane (MDPI, 2021)
    The barrier performance and structural lightening of organic materials are increasingly desired and constitute a major challenge for manufacturers, particularly for transport and packaging. A promising technique which tends ...
  • Forced assembly by multilayer coextrusion to create oriented graphene reinforced polymer nanocomposites 
    Article dans une revue avec comité de lecture
    LI, Xiguang; MCKENNA, Gregory; MIQUELARD-GARNIER, Guillaume; GUINAULT, Alain; SOLLOGOUB, Cyrille; ROZANSKI, Artur; ccREGNIER, Gilles (Elsevier, 2013)
    A potential advantage of platelet-like nanofillers as nanocomposite reinforcements is the possibility of achieving two-dimensional stiffening through planar orientation of the platelets. The ability to achieve improved ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales