• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Friction and Wear Performance of Biomaterials Alloy AISI 316L and Ti-6Al-7Nb

Article dans une revue avec comité de lecture
Auteur
FELLAH, Mamoun
266547 Université Badji Mokhtar [Annaba] = Badji Mokhtar University [Annaba] = (عنابة) جامعة باجي مختار–عنابة [UBMA]
AISSANI, Linda
LABAIZ, Mohamed
266547 Université Badji Mokhtar [Annaba] = Badji Mokhtar University [Annaba] = (عنابة) جامعة باجي مختار–عنابة [UBMA]
ABDUL SAMAD, Mohammed
242555 University of Malaya = Universiti Malaya [Kuala Lumpur, Malaisie] [UM]
ccMONTAGNE, Alex
211915 Mechanics surfaces and materials processing [MSMP]

URI
http://hdl.handle.net/10985/11960
Date
2016
Journal
Trends in biomaterials & artificial organs

Résumé

We became interested in this work to study the tribological behavior of two total hip replacements steel AISI 316L and titanium alloy Ti-6Al-7Nb tests performed in this work are essays with reciprocating movement. The tribological properties of wear by sliding (reciprocating) for the different samples were evaluated in the air on a tribometer with a tribotester software software following standards: ISO 7148, ASTM G99-95a, ASTM G 133-95, with a relative humidity of 33-38% at a temperature 24 to 27°C and a non-lubricated state. The ball 100C6 steel of 10 mm diameter, 835 HV hardness and Young’s modulus 310 GPa was chosen as the antagonist to prevent further chemical reactions. Three different speeds (1, 6 and 15 mms-1) and four normal forces (2, 4, 6 and 10 N) were applied, which allowed us to test twelve different conditions. The values of the friction coefficient obtained in this work are confirmed by the bibliographical results and meet the standards imposed by biomedical particularly at the joint surface state of hip prostheses.

Fichier(s) constituant cette publication

Nom:
MSMP_TIBAO_2016_MONTAGNE.pdf
Taille:
1.033Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Mechanics, Surfaces and Materials Processing (MSMP)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Synthesis, microstructural and tribological characterization of calcined nano-bioceramic α- al2o3, sintered at different temperatures 
    Communication sans acte
    FELLAH, Mamoun; AISSANI, Linda; LABAIZ, Mohamed; IOST, Alain; LAKMINE, F.; ABDUL SAMAD, Mohammed; NOUVEAU, Corinne; ccMONTAGNE, Alex (2016)
    The current research was undertaken to study the improvement of the tribological behavior of nanocrystalline bioceramic, α-alumina sample, produced by the calculations of gibbsite at different temperatures (300 to 1200°C), ...
  • Effect of Replacing Vanadium by Niobium and Iron on the Tribological Behavior of HIPed Titanium Alloys 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; ABDUL SAMAD, Mohammed; IOST, Alain; MOHAMED ZINE, Touhami; NOUVEAU, Corinne; ccMONTAGNE, Alex (Elsevier, 2017)
    This study aims to examine the effect of replacing vanadium by niobium and iron on the tribological behavior of hot-isostatic-pressed titanium alloy (Ti–6Al–4V) biomaterial, using a ball-on-disk-type oscillating tribometer, ...
  • Characterisation of R.F. magnetron sputtered Cr-N, Cr-Zr-N and Zr-N coatings 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; MECHACHETI, Said; TOUHAMI, Mohamed Zine; IOST, Alain; ABDUL SAMAD, Mohammed; ccMONTAGNE, Alex (Maney Publishing, 2017)
    Binary Cr-N, Zr-N and Cr-Zr-N films were synthesised using a R.F. reactive magnetron sputtering technique by co-sputtering Cr and Zr. The crystalline structure, morphology, mechanical and tribological properties of the ...
  • Thermal treatment effect on structural and mechanical properties of Cr–C coatings 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; ZAIRI, Amel; TOUHAMI, Mohamed Zine; DJEBAILI, Hamid; IOST, Alain; ABDUL SAMAD, Mohammed; NOUVEAU, Corinne; ccMONTAGNE, Alex (Maney Publishing, 2018)
    In the present study, the effect of thermal treatment on the mechanical and structural properties of chromium carbide coatings with different thicknesses is evaluated. The coatings were deposited by cathodic magnetron ...
  • Effect of Zr content on friction and wear behavior of Cr‐Zr‐N coating system 
    Article dans une revue avec comité de lecture
    FELLAH, Mamoun; AISSANI, Linda; ABDUL SAMAD, Mohammed; PURNAMA, Agung; DJEBAILI, Hamid; IOST, Alain; NOUVEAU, Corinne; ccMONTAGNE, Alex (Wiley, 2018)
    Nanostructured Cr‐Zr‐N thin film with different Zr content (0 to 48.8 at.%) was deposited, using an RF magnetron‐sputtering technique. The structural evolution and morphological changes were performed. The tribological ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales