• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Study of laser interaction in water flow confinement at high repetition rate

Article dans une revue avec comité de lecture
Auteur
BERTHE, Laurent
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
COURAPIED, Damien
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
EL KARNIGHI, Samy
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
PEYRE, Patrice
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
GORNY, Cyril
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
ROUCHAUSSE, Yann
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]

URI
http://hdl.handle.net/10985/17003
DOI
10.2351/1.5007947
Date
2017
Journal
Journal of Laser Applications

Résumé

This paper presents a study on the confined interaction with water flow for two successive laser pulses. The dynamic of the renewal of water films after shock produced by the laser is observed using a high speed camera. Pressure produced by the two pulses is measured from rear free surface velocity measurements using a velocimeter interferometry system for any reflector. The results show a threshold delay between the two laser pulses for which laser/target coupling of the second pulse decreases. This depends on the spot diameter, the laser intensity, and flow rate. This threshold can be calculated from the maximum jet diameter and flow rate. At an incident power density of 3 GW/cm2, a spot diameter of 1 mm, and a flow rate of 10 m/s, the maximum repetition rate ensuring target/coupling of successive laser pulses can be 1 kHz. The results open perspective for laser shock peening at high repetition rates.

Fichier(s) constituant cette publication

Nom:
PIMM_JLA_2017_BERTHE.pdf
Taille:
1.742Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Experimental and Numerical Analysis of Gas/Powder Flow for Different LMD Nozzles 
    Article dans une revue avec comité de lecture
    FERREIRA, Elise; COLIN, Christophe; MARION, Guillaume; GORNY, Cyril; COURAPIED, Damien; GUY, Jason; PEYRE, Patrice; ccDAL, Morgan (MDPI, 2020)
    The Laser Metal Deposition (LMD) process is an additive manufacturing method, which generates 3D structures through the interaction of a laser beam and a gas/powder stream. The stream diameter, surface density and focal ...
  • Laser surface patterning to enhance adhesion of plasma sprayed coatings 
    Article dans une revue avec comité de lecture
    KROMER, Robin; COSTIL, Sophie; CORMIER, Jonathan; COURAPIED, Damien; BERTHE, Laurent; PEYRE, Patrice; BOUSTIE, Michel (Elsevier, 2015)
    In thermal spraying, adhesive bond strength is a feature of surface properties. An adapted surface is studied with prior-surface treatments to enhance interface energy. This study deals with Ni–Al coatings on 2017 aluminum ...
  • Laser-delayed double shock-wave generation in water-confinement regime 
    Article dans une revue avec comité de lecture
    COURAPIED, Damien; BERTHE, Laurent; PEYRE, Patrice; COSTE, Frédéric; ZOU, J-P; SAUTIVET, A.-M. (Laser Institute of America, 2015)
    This paper investigates the different physical processes involved during laser-delayed double shock-wave generation in water-confined geometry. With this technique, two laser pulses, separated by a Δt duration, irradiate ...
  • Laser Patterning Pretreatment before Thermal Spraying: A Technique to Adapt and Control the Surface Topography to Thermomechanical Loading and Materials 
    Article dans une revue avec comité de lecture
    KROMER, Robin; COSTIL, Sophie; CORMIER, Jonathan; BERTHE, Laurent; PEYRE, Patrice; COURAPIED, Damien (ASM International/Springer, 2016)
    Coating characteristics are highly dependent on substrate preparation and spray parameters. Hence, the surface must be adapted mechanically and physicochemically to favor coating–substrate adhesion. Conventional surface ...
  • Laser adhesion test for thermal sprayed coatings on textured surface by laser 
    Article dans une revue avec comité de lecture
    COURAPIED, Damien; KROMER, Robin; BERTHE, Laurent; PEYRE, Patrice; COSTIL, Sophie; CORMIER, Jonathan; BOUSTIE, Michel; MILHET, Xavier (Laser Institute of America, 2016)
    The laser shock adhesion test (LASAT) is a technique allowing the generation of high tensile stresses in materials. The LASAT consists in focusing a pulsed laser beam on a water-confined target. The laser pulse crosses the ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales