• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Local electrochemical impedance spectroscopy study of the influence of ageing in air and laser shock processing on the micro-electrochemical behaviour of AA2050-T8 aluminium alloy

Article dans une revue avec comité de lecture
Auteur
KRAWIEC, Halina
445585 AGH University of Science and Technology [Krakow, PL] [AGH UST]
VIGNAL, Vincent
496957 Laboratoire Interdisciplinaire Carnot de Bourgogne [ICB]
AMAR, Hassan
496957 Laboratoire Interdisciplinaire Carnot de Bourgogne [ICB]
PEYRE, Patrice
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
175453 Arts et Métiers ParisTech

URI
http://hdl.handle.net/10985/17904
DOI
10.1016/j.electacta.2011.01.091
Date
2011
Journal
Electrochimica Acta

Résumé

In the present paper, the micro-electrochemical behaviour of AA2050-T8 in 0.1 M NaCl was first studied after polishing by means of local electrochemical impedance spectroscopy and field-emission scanning electron microscopy/electron dispersive spectroscopy (FE-SEM/EDS). The influence of ageing in air and LSP was then investigated. Ageing in air for three months led to an increase in the charge transfer resistance. This was clearly observed in sites surrounding constituent particles where the charge transfer resistance was in the order of 1 MΩ cm2 (instead of 10-3 MΩ cm2 after polishing). Increased passivity around particles was confirmed from FE-SEM/EDS analysis. On the other hand, the effect of LSP on the behaviour of the matrix was found to be extremely beneficial. Both charge transfer and oxide film resistances were sharply increased to approximately 0.35 MΩ cm 2 and 1 MΩ cm2, respectively, as opposed to approximately 1.9 × 10-3 MΩ cm2 and 4.2 × 10-3 MΩ cm2, respectively, after ageing in air. This was attributed to the presence of compressive stresses at the specimen surface after LSP treatment. Stress values were determined from XRD measurements.

Fichier(s) constituant cette publication

Nom:
PIMM_EA_2011_PEYRE.pdf
Taille:
900.2Ko
Format:
PDF
Description:
Article
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Influence of the microstructure and laser shock processing (LSP) on the corrosion behaviour of the AA2050-T8 aluminium alloy 
    Article dans une revue avec comité de lecture
    AMAR, Hassan; KRAWIEC, Halina; JOSSE, Claudie; PEYRE, Patrice; DA SILVA, S. N.; DICK, Luis Federico (Elsevier, 2011)
    The corrosion behaviour of AA2050-T8 was studied after polishing and after laser shock processing (LSP) treatment using the electrochemical microcell technique and the SVET. After polishing, pitting at constituent particles ...
  • Finite element analysis of laser shock peening of 2050-T8 aluminum alloy 
    Article dans une revue avec comité de lecture
    HFAIEDH, Neila; PEYRE, Patrice; SONG, Hongbin; POPA, Ioana; JI, Vincent; VIGNAL, Vincent (Elsevier, 2015)
    Laser shock processing is a recently developed surface treatment designed to improve the mechanical properties and fatigue performance of materials, by inducing a deep compressive residual stress field. The purpose of this ...
  • Analysis of laser shock waves and resulting surface deformations in an Al-Cu-Li aluminum alloy 
    Article dans une revue avec comité de lecture
    PEYRE, Patrice; BERTHE, Laurent; VIGNAL, Vincent; POPA, Ioana; BAUDIN, T. (IOP Publishing, 2012)
    Laser shock processing is now a recognized surface treatment for improving fatigue or corrosion behaviour of metallic materials through the generation of a compressive stress field. In turn, the analysis of shock wave ...
  • Analysis of laser shock waves and resulting surface deformations in an Al-Cu-Li aluminium alloy 
    Article dans une revue avec comité de lecture
    ccPEYRE, Patrice; BERTHE, Laurent; VIGNAL, Vincent; POPA, Ioana; BAUDIN, Thierry (IOP Publishing, 2012)
    Laser shock processing (LSP) is now a recognized surface treatment for improving fatigue or corrosion behaviour of metallic materials through the generation of a compressive stress field. In turn, the analysis of shock ...
  • Analysis of As-Built Microstructures and Recrystallization Phenomena on Inconel 625 Alloy Obtained via Laser Powder Bed Fusion (L-PBF) 
    Article dans une revue avec comité de lecture
    DE TERRIS, Thibaut; CASTELNAU, Olivier; HADJEM-HAMOUCHE, Zehoua; ccHADDADI, Halim; MICHEL, Vincent; PEYRE, Patrice (MDPI AG, 2021)
    The microstructures induced by the laser-powder bed fusion (L-PBF) process have been widely investigated over the last decade, especially on austenitic stainless steels (AISI 316L) and nickel-based superalloys (Inconel ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales