Laboratoire Ingénierie des fluides Systèmes énergétiques (LIFSE): Soumissions récentes

Voici les éléments 43-49 de 59

    • In-Process Monitoring of Temperature Evolution during Fused Filament Fabrication: A Journey from Numerical to Experimental Approaches 
      Article dans une revue avec comité de lecture
      VANAEI, Hamid Reza; ccSHIRINBAYAN, Mohammadali; ccDELIGANT, Michael; ccKHELLADI, Sofiane; ccTCHARKHTCHI, Abbas (MDPI AG, 2021)
      Fused filament fabrication (FFF), an additive manufacturing technique, unlocks alternative possibilities for the production of complex geometries. In this process, the layer-by-layer deposition mechanism and several heat ...
    • Experimental study of a novel centrifugal compressor with two successive and independent rotors 
      Article dans une revue avec comité de lecture
      NGUYEN, Van-Thang; ABED, Cheikh Brahim; DANLOS, Amelie; ccRAVELET, Florent; PARIDAENS, Richard; ccDELIGANT, Michael; ccKHELLADI, Sofiane; ccBAKIR, Farid (American Society of Mechanical Engineers, 2021)
      The present study deals with a low pressure-ratio centrifugal compressor consisting of two counter-rotating rotors called a Counter-Rotating Centrifugal Compressor (CRCC). The design method based on the loss model was ...
    • Controlled release from polyurethane films: Drug release mechanisms 
      Article dans une revue avec comité de lecture
      ABBASNEZHAD, Navideh; ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; ccKOUIDRI, SMAINE; SALAHINEJAD, Erfan; ccTCHARKHTCHI, Abbas; ccBAKIR, Farid (Wiley, 2021)
      In this study, polyurethane-films loaded with diclofenac were used to analyze the drug release kinetics and mechanisms. For this purpose, the experimental procedures were developed under static and dynamic conditions with ...
    • Rotational Molding of Polyamide-12 Nanocomposites: Modeling of the Viscoelastic Behavior 
      Article dans une revue avec comité de lecture
      ccSHIRINBAYAN, Mohammadali; MONTAZERI, A.; NOURI SEDEH, M.; ABBASNEZHAD, Navideh; ccTCHARKHTCHI, Abbas; ccFITOUSSI, Joseph (Springer Verlag, 2021)
      Nowadays, polyamide 12 (PA-12) is considered as an interesting polymer in the rotomolding process to manufacture different pieces like the liner part in the storage hydrogen tank (type IV). In this study, the pure polyamide-12 ...
    • Multiscale damage analysis of the tension‐tension fatigue behavior of a low‐density sheet molding compound 
      Article dans une revue avec comité de lecture
      ccSHIRINBAYAN, Mohammadali (Wiley, 2021)
      This article presents the experimental findings of tension-tension stress-controlled fatigue tests performed on low-density sheet molding compound (LD-SMC). LD-SMC composite is a type of SMC including a polyester resin ...
    • On the importance of physical and mechanical properties of PLGA films during drug release 
      Article dans une revue avec comité de lecture
      ABBASNEZHAD, Navideh; ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; ccTCHARKHTCHI, Abbas; ccBAKIR, Farid (Elsevier, 2021)
      Physical and mechanical properties of the drug-incorporated polymer play a significant role in the release behavior from the drug carriers. Understanding the relative extent of variation in the physical and mechanical ...
    • Experimental study of PLA thermal behavior during fused filament fabrication 
      Article dans une revue avec comité de lecture
      VANAEI, Hamid Reza; ccSHIRINBAYAN, Mohammadali; COSTA, Sidonie Fernandes; DUARTE, Fernando Moura; COVAS, José António; ccDELIGANT, Michael; ccKHELLADI, Sofiane; ccTCHARKHTCHI, Abbas (Wiley, 2021)
      Fused filament fabrication (FFF) is an additive manufacturing technique that is used to produce prototypes and a gradually more important processing route to obtain final products. Due to the layer-by-layer deposition ...