Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM): Soumissions récentes

Voici les éléments 1065-1071 de 1329

    • Structural and magnetic properties of Co2MnSi thin films 
      Article dans une revue avec comité de lecture
      BELMEGUENAI, M; ZIGHEM, F; FAURIE, D; TUZCUOGLU, H.; CHERIF, Salim Mourad; WESTERHOLT, K; SEILER, Wilfrid; MOCH, P (Wiley, 2012)
      Co2MnSi (CMS) films of different thicknesses (20, 50, and 100 nm) were grown by radio frequency (RF) sputtering on a-plane sapphire substrates. Our X-rays diffraction (XRD) study shows that, in all the samples, the cubic ...
    • Phénomènes dynamiques en usinage : Prédiction de l’état géométrique des surfaces usinées 
      Communication sans acte
      COFFIGNAL, Gérard; DUCHEMIN, Jérôme; ILLOUL, Lounès; GENGEMBRE, Christophe; ccLORONG, Philippe; ccGUSKOV, Mikhail (2013)
      Présentation concernant la modélisation des phénomènes dynamiques en usinage. Cette modélisation a pour particularité de permettre la prédiction de la géométrie des surfaces usinées (défauts de forme, d'ondulation) que la ...
    • Introduction of variability into pantograph–catenary dynamic simulations 
      Article dans une revue avec comité de lecture
      VO VAN, Olivier; MASSAT, Jean-Pierre; LAURENT, Christophe; BALMES, Etienne (Taylor & Francis, 2014)
      Currently, pantograph-catenary dynamic simulations are mainly based on deterministic approaches. However, the contact force between catenary and pantograph depends on many key parameters that are not always quantified ...
    • Simulating the Heat Distortiion of a Cast Iron Brake Disc during Dry Machining 
      Communication avec acte
      BOYER, Henri-François; FRABOLOT, M.; KOPPKA, Frank; ccLORONG, Philippe; ccRANC, Nicolas (2012)
      The application of MQL or dry machining in mass production becomes more and more accepted. Dry (MQL) machining is a very efficient solution to reduce the usage of cutting fluids and represents an effective measure for an ...
    • On some aspects of the CNEM implementation in 3D in order to simulate high speed machining or shearing 
      Article dans une revue avec comité de lecture
      ILLOUL, Lounès; ccLORONG, Philippe (Elsevier, 2011)
      his paper deals with the implementation in 3D of the constrained natural element method (CNEM) in order to simulate material forming involving large strains. The CNEM is a member of the large family of mesh-free methods, ...
    • Dissipation Assessments During Dynamic Very High Cycle Fatigue Tests 
      Article dans une revue avec comité de lecture
      BLANCHE, Antoine; CHRYSOCHOOS, André; ccRANC, Nicolas; ccFAVIER, Véronique (Society for Experimental Mechanics, 2015)
      This paper presents an experimental device developed to detect and estimate dissipated energy during very high cycle fatigue tests (VHCF) at high loading frequency (20 kHz) and low stress (i.e. far below the yield stress). ...
    • OSCAR Statement of Methods 
      Article dans une revue avec comité de lecture
      MASSAT, Jean-Pierre; BALMES, Etienne; BIANCHI, Jean-Philippe; VAN KALSBEEK, Guido (Taylor & Francis, 2015)
      OSCAR (Outil de Simulation du CAptage pour la Reconnaissance des défauts) is the pantograph–catenary dynamic software developed by Société Nationale des Chemins de fer Français (SNCF) since 2004. A three-dimensional finite ...