• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

An overview of filtration efficiency through the masks: Mechanisms of the aerosols penetration

Type
Articles dans des revues avec comité de lecture
Auteur
TCHARKHTCHI, Abbas
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
ABBASNEZHAD, N.
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]
ZARBINI SEYDANI, M.
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]
ZIRAK, N.
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]
FARZANEH, S.
571200 P4Tech [P4Tech]
SHIRINBAYAN, Mohammadali
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]

URI
http://hdl.handle.net/10985/19215
DOI
10.1016/j.bioactmat.2020.08.002
Date
2021
Journal
Bioactive Materials

Résumé

The masks have always been mentioned as an effective tool against environmental threats. They are considered as protective equipment to preserve the respiratory system against the non-desirable air droplets and aerosols such as the viral or pollution particles. The aerosols can be pollution existence in the air, or the infectious airborne viruses initiated from the sneezing, coughing of the infected people. The filtration efficiency of the different masks against these aerosols are not the same, as the particles have different sizes, shapes, and properties. Therefore, the challenge is to fabricate the filtration masks with higher efficiency to decrease the penetration percentage at the nastiest conditions. To achieve this concept, knowledge about the mechanisms of the penetration of the aerosols through the masks at different effective environmental conditions is necessary. In this paper, the literature about the different kinds of face masks and respiratory masks, common cases of their application, and the advantages and disadvantages of them in this regard have been reviewed. Moreover, the related mechanisms of the penetration of the aerosols through the masks are discussed. The environmental conditions affecting the penetration as well as the quality of the fabrication are studied. Finally, special attention was given to the numerical simulation related to the different existing mechanisms.

Fichier(s) constituant cette publication

Nom:
PIMM_BM_ 2020_TCHARKHTCHI.pdf
Taille:
3.995Mo
Format:
PDF
Description:
Article
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Ingénierie des fluides Systèmes énergétiques (LIFSE)
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • In vitro study of drug release from various loaded polyurethane samples and subjected to different non-pulsed flow rates 
    ABBASNEZHAD, N; SHIRINBAYAN, Mohammadali; TCHARKHTCHI, Abbas; BAKIR, Farid (ELSEVIER, 2020)
    Drug-eluting implants with a polymeric matrix are currently widely used and the interest of modeling their behavior is increasing. This article aims to present preliminary results of an in vitro under steady flow, study ...
  • Some New Concepts of Shape Memory Effect of Polymers 
    TCHARKHTCHI, Abbas; ABDALLAH-ELHIRTSI, Sofiane; EBRAHIMI, Kambiz; FITOUSSI, Joseph; SHIRINBAYAN, Mohammadali; FARZANEH, Sedigheh (MDPI, 2014)
    In this study some new concepts regarding certain aspects related to shape memory polymers are presented. A blend of polylactic acid (PLA) (80%) and polybutylene succinate (PBS) (20%) was prepared first by extrusion, then ...
  • Effect of a Post-Fatigue Damage on the Residual Dynamic Behavior of Advanced-SMC Composites 
    SHIRINBAYAN, Mohammadali; FITOUSSI, Joseph; MERAGHNI, Fodil; FARZANEH, S.; SUROWIEC, Benjamin; TCHARKHTCHI, Abbas (Springer, 2019)
    The purpose of this article is to investigate the effect of an initial pre-damage induced by a fatigue loading on the tensile dynamic behavior of Advanced Sheet Molding Compounds (A-SMC). Tension-tension fatigue preloading ...
  • Mechanical characterization of a Low Density Sheet Molding Compound (LD-SMC): Multi-scale damage analysis and strain rate effect 
    SHIRINBAYAN, M; FITOUSSI, J; ABBASNEZHAD, N; MERAGHNI, Fodil; SUROWIEC, Benjamin; TCHARKHTCHI, Abbas (Elsevier, 2017)
    This paper presents the results of an overall experimental characterization of the mechanical behavior of a Low Density Sheet Molding Compound (LD-SMC). LD-SMC is a polyester matrix containing mineral charge (CaCO3) ...
  • Influence of loading conditions on the overall mechanical behavior of polyether-ether-ketone (PEEK) 
    ABBASNEZHAD, N; KHAVANDI, Alireza; FITOUSSI, JOSEPH; ARABI, H; SHIRINBAYAN, M; TCHARKHTCHI, Abbas (Elsevier, 2018)
    Testing methods have been developed to compare the mechanical responses and failure behavior of polyether-ether-keton (PEEK) thermoplastic polymer; under quasi-static, high strain rate tensile tests and fatigue loading. ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales