• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Influence of beam diameter on Laser Powder Bed Fusion (L-PBF) process

Article dans une revue avec comité de lecture
Auteur
SOW, M.C.
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
DE TERRIS, Thibaut
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
CASTELNAU, Olivier
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
HADJEM-HAMOUCHE, Zehoua
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
COSTE, Frédéric
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
FABBRO, Rémy
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
PEYRE, Patrice
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]

URI
http://hdl.handle.net/10985/19357
DOI
10.1016/j.addma.2020.101532
Date
2020
Journal
Additive Manufacturing

Résumé

The use of large beams in the Laser Powder Bed Fusion (L-PBF) process has been receiving increasing attention for the past few years and may widen the dissemination of this technology in the industry, as well as help increase the production volume. In this paper, a detailed comparison is presented between a usual 80 μm diameter Gaussian laser spot and a 500 μm diameter top-hat laser beam. The following benefits of a large and homogeneous beam could be demonstrated: (1) a moderate increase of productivity by reducing the number of scan lines, (2) a nearly total suppression of spatters and powder bed degradation (local loss of powder homogeneity caused by the redeposition of spatters) due to the low volume energy densities carried out and the limitation of deleterious vaporization effects, (3) the manufacturing of near fully dense Inconel 625 parts, especially in the hatching zones. Last, the occurrence of larger thermal effects induced by the large beam L-PBF was discussed by comparing two distinct definitions of the laser energy density: at a local (melt pool) scale, and at a global (the whole manufactured part) level.

Fichier(s) constituant cette publication

Nom:
PIMM_AM_ 2020_SOW.pdf
Taille:
4.284Mo
Format:
PDF
Description:
Article
Fin d'embargo:
2021-06-01
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Analysis of As-Built Microstructures and Recrystallization Phenomena on Inconel 625 Alloy Obtained via Laser Powder Bed Fusion (L-PBF) 
    Article dans une revue avec comité de lecture
    DE TERRIS, Thibaut; CASTELNAU, Olivier; HADJEM-HAMOUCHE, Zehoua; HADDADI, Halim; MICHEL, Vincent; PEYRE, Patrice (MDPI AG, 2021)
    The microstructures induced by the laser-powder bed fusion (L-PBF) process have been widely investigated over the last decade, especially on austenitic stainless steels (AISI 316L) and nickel-based superalloys (Inconel ...
  • Optimization and comparison of porosity rate measurement methods of Selective Laser Melted metallic parts 
    Article dans une revue avec comité de lecture
    DE TERRIS, Thibaut; ANDREAU, Olivier; PEYRE, Patrice; ADAMSKI, Frédéric; KOUTIRI, Imade; GORNY, Cyril; DUPUY, Corinne (Elsevier, 2019)
    The systematic occurrence of porosities inside selective laser melted (SLM) parts is a well-known phenomenon. In order to improve the density of SLM parts, it is important not only to assess the physical origin of the ...
  • Experimental study and micromechanical modelling of the effective elastic properties of Fe–TiB2 composites 
    Article dans une revue avec comité de lecture
    DORHMI, Khaoula; DERRIEN, Katell; HADJEM-HAMOUCHE, Zehoua; MORIN, Léo; BONNET, Frédéric; CHEVALIER, Jean-Pierre (Elsevier BV, 2021)
    The aim of this paper is to investigate the effective properties of Fe–TiB2 composites obtained after hot or cold rolling. The elastic moduli of both hot and cold rolled composites are measured experimentally using several ...
  • Texture control of 316L parts by modulation of the melt pool morphology in selective laser melting 
    Article dans une revue avec comité de lecture
    ANDREAU, Olivier; KOUTIRI, Imade; PEYRE, Patrice; PENOT, Jean-Daniel; SAINTIER, Nicolas; PESSARD, Etienne; DE TERRIS, Thibaut; DUPUY, Corinne; BAUDIN, Thierry (Elsevier, 2019)
    In this study, 316L parts were fabricated with the selective laser melting additive layer manufacturing process using unidirectional laser scan to control their texture. The melt pool shape, microstructure and texture of ...
  • A homogenization-based damage model for stiffness loss in ductile metal-matrix composites(Article) 
    Article dans une revue avec comité de lecture
    DORHMI, Khaoula; MORIN, LEO; DERRIEN, Katell; HADJEM-HAMOUCHE, Zehoua; CHEVALIER, Jean - Pierre (Elsevier, 2020)
    The aim of this paper is to develop a homogenized model that permits to describe the progressive loss of stiffness observed experimentally on ductile metal-matrix composites subjected to mechanical loadings. A two-step ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales