• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire de Conception Fabrication Commande (LCFC)
  • Voir le document
  • Accueil de SAM
  • Laboratoire de Conception Fabrication Commande (LCFC)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Control of an Underactuated 4 Cable-Driven Parallel Robot using Modified Input-Output Feedback Linearization

Article dans une revue avec comité de lecture
Auteur
KUMAR, Atal Anil
ABBA, Gabriel
ANTOINE, Jean-François
107452 Laboratoire de Conception Fabrication Commande [LCFC]

URI
http://hdl.handle.net/10985/20277
DOI
10.1016/j.ifacol.2020.12.1380
Date
2020
Journal
IFAC-PapersOnLine

Résumé

This paper presents the control of an underactuated four Cable-Driven Parallel Robot (CDPR) using a modified input-output feedback linearization technique. The effect of internal dynamics (due to the underactuated degrees of freedom of the CDPR) on the behavior of the moving platform is presented to highlight the need of an improved controller to stabilize the system outputs. A modified control scheme is then proposed as a solution to obtain stable system outputs. A structure with two separate branches modeled to simultaneously act on the control inputs and the mathematical calculations are done using the well-established equations of nonlinear control theory. Following this, the response of the system to modified control law is then verified by simulation. A comparison between the classical and modified feedback linearization shown to illustrate the significant improvement

Fichier(s) constituant cette publication

Nom:
LCFC_IFAC_2020_KUMAR.pdf
Taille:
773.4Ko
Format:
PDF
Fin d'embargo:
2021-06-01
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire de Conception Fabrication Commande (LCFC)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Input-Output Feedback Linearization for the Control of a 4 Cable-Driven Parallel Robot 
    Article dans une revue avec comité de lecture
    KUMAR, Atal Anil; ABBA, Gabriel; ANTOINE, Jean-François (Elsevier, 2019)
    This paper presents the control of an under-constrained 4 Cable-Driven Parallel Robot (CDPR) using input-output feedback linearization technique. The dynamic model of the CDPR is first formulated by taking into account the ...
  • Design Elements for high speed SRM 
    Article dans une revue avec comité de lecture
    ABBA, Gabriel; ANTOINE, Jean-François; SAUVEY, Christophe; VISA, Codrut (2004)
    This paper deals with the study of high speed switched reluctance motors and their pre-dimensioning. The predimensioning is tackled towards the inductance profile and the torque generation. Then, the power density is ...
  • Computational and experimental investigation of flow over a transient pitching hydrofoil 
    Article dans une revue avec comité de lecture
    DUCOIN, Antoine; ccASTOLFI, Jacques Andre; DENISET, François; SIGRIST, Jean-François (Elsevier, 2009)
    The present study is developed within the framework of marine structure design operating in transient regimes. It deals with an experimental and numerical investigation of the time–space distribution of the wall-pressure ...
  • Management of product characteristics uncertainty based on Formal Logic and Characteristics Properties Model 
    Article dans une revue avec comité de lecture
    QURESHI, Ahmed Jawad; ANTOINE, Jean-François; EISENBART, Boris; BLESSING, Lucienne; ccDANTAN, Jean-Yves (Elsevier, 2013)
    Uncertainty in product characteristics is ubiquitous in any engineering system at all the stages of product life-cycle. Considering uncertainty from different sources during the product design phase is critical to its ...
  • A product functional modelling approach based on the energy flow by using characteristics-properties modelling 
    Article dans une revue avec comité de lecture
    BABAEIZADEH MALMIRY, Roozbeh; ccDANTAN, Jean-Yves; ccPAILHES, Jerome; ANTOINE, Jean-François (Taylor & Francis, 2016)
    The main objective in designing a product is to satisfy the required needs. So, the designer aims to design the product’s structure based on the required function of the product. Therefore, in the design process, the link ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales