Inverse Identification of the Ductile Failure Law for Ti6Al4V Based on Orthogonal Cutting Experimental Outcomes
Article dans une revue avec comité de lecture
Despite the prevalence of machining, tools and cutting conditions are often chosen based on empirical databases, which are hard to be made, and they are only valid in the range of conditions tested to develop it. Predictive numerical models have thus emerged as a promising approach. To function correctly, they require accurate data related to appropriate material properties (e.g., constitutive models, ductile failure law). Nevertheless, material characterization is usually carried out through thermomechanical tests, under conditions far different from those encountered in machining. In addition, segmented chips observed when cutting titanium alloys make it a challenge to develop an accurate model. At low cutting speeds, chip segmentation is assumed to be due to lack of ductility of the material. In this work, orthogonal cutting tests of Ti6Al4V alloy were carried out, varying the uncut chip thickness from 0.2 to 0.4 mm and the cutting speed from 2.5 to 7.5 m/min. The temperature in the shear zone was measured through infrared measurements with high resolution. It was observed experimentally, and in the FEM, that chip segmentation causes oscillations in the workpiece temperature, chip thickness and cutting forces. Moreover, workpiece temperature and cutting force signals were observed to be in counterphase, which was predicted by the ductile failure model. Oscillation frequency was employed in order to improve the ductile failure law by using inverse simulation, reducing the prediction error of segmentation frequency from more than 100% to an average error lower than 10%.
Fichier(s) constituant cette publication
Cette publication figure dans le(s) laboratoire(s) suivant(s)
Visualiser des documents liés par titre, auteur, créateur et sujet.
Communication avec acteSELA, Andres; ORTIZ-DE-ZARATE, Gorka; SOLER, Daniel; ARISTIMUÑO, Patxi; SORIANO, Denis; GERMAIN, Guénaël; DUCOBU, François; ARRAZOLA, Pedro José (Elsevier BV, 2020)Surface integrity directly affects the mechanical behavior of the workpiece, which is especially relevant on fatigue behavior. To characterize the quality of the machined surface, aspects such as material damage, roughness ...
Article dans une revue avec comité de lectureSELA, Andres; ORTIZ-DE-ZARATE, Gorka; SOLER, Daniel; GERMAIN, Guénaël; ARISTIMUÑO, Patxi; ARRAZOLA, Pedro José (Elsevier BV, 2021)Finite Element Modelling used to predict machining outcomes needs to be supplied with the appropriate material thermomechanical properties which are obtained by specific testing devices and methodologies. However, these ...
Mechanical characterization and modelling of Inconel 718 material behavior for machining process assessment Article dans une revue avec comité de lectureITURBE, Ariane; GIRAUD, Eliane; HORMAETXE, Exabier; GARAY, Ainhara; GERMAIN, Guénaël; OSTOLAZA, Koldo; ARRAZOLA, Pedro José (Elsevier BV, 2017)Nickel based alloys are extensively used in the aerospace industry due to the excellent corrosion resistance and high mechanical properties that are maintained up to elevated temperatures (600–800 °C). However, these ...
Corrigendum to “Mechanical characterization and modelling of Inconel 718 material behavior for machining process assessment” [Mater. Sci. Eng. A 682 (2017) 441–453] Article dans une revue avec comité de lectureITURBE, Ariane; GIRAUD, Eliane; HORMAETXE, Exabier; GARAY, Ainhara; GERMAIN, Guénaël; OSTOLAZA, Koldo; ARRAZOLA, Pedro José (Elsevier, 2019)Corrigendum to “Mechanical characterization and modelling of Inconel 718 material behavior for machining process assessment” [Mater. Sci. Eng. A 682 (2017) 441–453]
Comparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718 Article dans une revue avec comité de lectureCHAABANI, Sana; ARRAZOLA, Pedro José; AYED, Yessine; MADARIAGA, Aitor; TIDU, Albert; GERMAIN, Guénaël (Elsevier, 2020)The most important challenges when machining difficult-to-cut alloys used in critical applications consist mainly in increasing tool life as well as improving the component surface integrity. In particular, the nickel based ...