• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Mechanical strength and shape accuracy optimization of polyamide FFF parts using grey relational analysis

Article dans une revue avec comité de lecture
Auteur
SHAKERI, Zohreh
ZIRAK, Nader
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]
ccSHIRINBAYAN, Mohammadali
1003528 Laboratoire d'Ingénierie des Fluides et des Systèmes Énergétiques [LIFSE]
ccBENFRIHA, Khaled
86289 Laboratoire Procédés et Ingénierie en Mécanique et Matériaux [PIMM]
127758 Laboratoire Conception de Produits et Innovation [LCPI]
1003434 Arts et Métiers Sciences et Technologies

URI
http://hdl.handle.net/10985/22716
DOI
10.1038/s41598-022-17302-z
Date
2022-07
Journal
Scientific reports (Nature)

Résumé

This paper investigates the effect of different additive manufacturing process parameters such as chamber temperature, Printing temperature, layer thickness, and print speed on five essential parameters that characterize the manufactured components: cylindricity, circularity, strength, and Young’s modulus, and deformation by Gray Relational Analysis method simultaneously. Taguchi method was used to design the experiments, and the PA6 cylindrical parts were fabricated using a German RepRap X500® 3D printer. Then the Gray Relational Grade (GRG) values were calculated for all experiments. In the 8th trial, the highest value of GRG was observed. Then, to discover the optimal parameters, the GRG data were analyzed using ANOVA and S/N analysis, and it was determined that the best conditions for enhancing GRG are 60 °C in the chamber temperature, 270 °C in the printing temperature, 0.1 mm layer thickness, and 600 mm/min print speed. Finally, by using optimal parameters, a verification test was performed, and new components were investigated. Finally, comparing the initial GRG with the GRG of the experiments showed an improvement in the gray relational grade (14%) which is accompanying with improving of GRG value.

Fichier(s) constituant cette publication

Nom:
PIMM_NATURE-SR_2022-SHAKERI.pdf
Taille:
3.356Mo
Format:
PDF
Description:
Mechanical strength and shape ...
Fin d'embargo:
2023-02-01
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Conception de Produits et Innovation (LCPI)
  • Laboratoire Ingénierie des fluides Systèmes énergétiques (LIFSE)
  • Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Stereolithography of (meth)acrylate-based photocurable resin: Thermal and mechanical properties 
    Article dans une revue avec comité de lecture
    ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; ccBENFRIHA, Khaled; ccTCHARKHTCHI, Abbas; ccDELIGANT, Michael (WILEY, 2022)
    Additive manufacturing (AM) has attracted a lot of attention in the industry and studies due to the ability to fabricate parts in different sizes and shapes along with economic costs. Among the different three-dimensional ...
  • Mechanical strength and shape accuracy optimization of polyamide FFF parts using grey relational analysis 
    Article dans une revue avec comité de lecture
    SHAKERI, Zohreh; ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; ccBENFRIHA, Khaled (Springer Science and Business Media LLC, 2022-07-30)
    AbstractThis paper investigates the effect of different additive manufacturing process parameters such as chamber temperature, Printing temperature, layer thickness, and print speed on five essential parameters that ...
  • Effect of build orientation and post-curing of (meth)acrylate‐based photocurable resin fabricated by stereolithography on the mechanical behavior from quasi-static to high strain rate loadings 
    Article dans une revue avec comité de lecture
    ccSHIRINBAYAN, Mohammadali; ZIRAK, Nader; SADDAOUI, Ouiza; MAMMERI, Amrid; AZZOUZ, Kamel; ccBENFRIHA, Khaled; ccTCHARKHTCHI, Abbas; ccFITOUSSI, Joseph (Springer Science and Business Media LLC, 2022-10)
    Stereolithography (SLA) is becoming an important fabrication method among the different additive manufacturing techniques. This study investigates the effect of high strain rate on mechanical behavior, considering the fact ...
  • On the importance of physical and mechanical properties of PLGA films during drug release 
    Article dans une revue avec comité de lecture
    ABBASNEZHAD, Navideh; ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; ccTCHARKHTCHI, Abbas; ccBAKIR, Farid (Elsevier, 2021)
    Physical and mechanical properties of the drug-incorporated polymer play a significant role in the release behavior from the drug carriers. Understanding the relative extent of variation in the physical and mechanical ...
  • Effect of molecular weight on crystallization behavior of poly (lactic acid) under isotherm and non‐isotherm conditions 
    Article dans une revue avec comité de lecture
    ZIRAK, Nader; ccSHIRINBAYAN, Mohammadali; FARZANEH, Sedigheh; ccTCHARKHTCHI, Abbas (Wiley, 2022)
    The effect of molecular weight on the crystallization behavior of poly(lactic acid) (PLA) both isothermally and non-isothermally was studied using differential scanning calorimetry and polarized optical microscopy. Two ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales