• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • Voir le document
  • Accueil de SAM
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Investigations of grinding burn on a nitrided steel

Communication avec acte
Auteur
ccLAVISSE, Bruno
211916 Laboratoire Angevin de Mécanique, Procédés et InnovAtion [LAMPA]
WEISS, Laurent
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
ccKOKANYAN, Ninel
202503 Laboratoire Matériaux Optiques, Photonique et Systèmes [LMOPS]
LEFEBVRE, André
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
HENRION, Emerik
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
SINOT, Olivier
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
TIDU, Albert
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]

URI
http://hdl.handle.net/10985/22983
DOI
10.1016/j.procir.2022.03.086
Date
2022-06-01

Résumé

Grinding process may lead to the occurrence of grinding burn. When the temperature in the contact zone gets too high, it may lead to damage of the workpiece. The target of this study was to characterize changes occurring in the material after grinding burn on a nitrided steel. The microstructural changes after burn were quantified, by using residual stresses, Raman spectroscopy was also use to detect and characterize different oxides, appearing after grinding burn. The study highlights the possibilities of using this last non destructive method for detecting and quantifying grinding burn.

Fichier(s) constituant cette publication

Nom:
LAMPA_PROCEDIACIRP 6_2022_LAVI ...
Taille:
1.140Mo
Format:
PDF
Voir/Ouvrir
CC BY-NC-ND
Ce document est diffusé sous licence CC BY-NC-ND

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Comparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718 
    Article dans une revue avec comité de lecture
    CHAABANI, Sana; ARRAZOLA, Pedro José; ccAYED, Yessine; MADARIAGA, Aitor; TIDU, Albert; ccGERMAIN, Guénaël (Elsevier, 2020)
    The most important challenges when machining difficult-to-cut alloys used in critical applications consist mainly in increasing tool life as well as improving the component surface integrity. In particular, the nickel based ...
  • Impact of the initial microstructure and the loading conditions on the deformation behavior of the Ti17 titanium alloy 
    Article dans une revue avec comité de lecture
    BEN BOUBAKER, Houssem; ccMAREAU, Charles; ccAYED, Yessine; ccGERMAIN, Guénaël; TIDU, Albert (Springer Verlag, 2019)
    In this work, the impact of the microstructure and the loading conditions on the mechanical behavior of a β-rich Ti17 titanium alloy is investigated. For this purpose, two different initial microstructures are considered ...
  • A crystal plasticity-based constitutive model for near-β titanium alloys under extreme loading conditions: Application to the Ti17 alloy 
    Article dans une revue avec comité de lecture
    BEN BOUBAKER, Houssem; ccMAREAU, Charles; ccAYED, Yessine; ccGERMAIN, Guénaël; TIDU, Albert (Elsevier BV, 2022-01-07)
    A crystal plasticity-based constitutive model is proposed to describe the thermo-mechanical behavior of the Ti17 titanium alloy subjected to extreme loading conditions. The model explicitly incorporates the effect of the ...
  • Surface Integrity When Machining Inconel 718 Using Conventional Lubrication and Carbon Dioxide Coolant 
    Communication avec acte
    CHAABANI, Sana; ARRAZOLA, Pedro José; ccAYED, Yessine; MADARIAGA, Aitor; TIDU, Albert; ccGERMAIN, Guénaël (Elsevier BV, 2020)
    Surface integrity induced by machining process affects strongly the performance of functional products, for instance, the fatigue life as well as the resistance to stress corrosion cracking. Consequently, it is relevant ...
  • Reuse of medical face masks in domestic and community settings without sacrificing safety: Ecological and economical lessons from the Covid-19 pandemic 
    Article dans une revue avec comité de lecture
    ALCARAZ, Jean-Pierre; LE COQ, Laurence; POURCHEZ, Jérémie; THOMAS, Dominique; CHAZELET, Sandrine; BOUDRY, Isabelle; BARBADO, Maud; SILVENT, Sophie; DESSALE, Claire; ANTOINE, Fabienne; GUIMIER-PINGAULT, Catherine; CORTELLA, Laurent; ROUIF, Sophie; BARDIN-MONNIER, Nathalie; CHARVET, Augustin; DUFAUD, Olivier; LECLERC, Lara; MONTIGAUD, Yoann; LAURENT, Coralie; VERHOEVEN, Paul; JOUBERT, Aurélie; BOUHANGUEL, Ala; ANDRES, Yves; GAFFÉ, Joël; MARTIN, Donald K.; HUET, Christophe; BOISSET, Sandrine; MAURIN, Max; RUMEAU, Pascal; CHARLOT, Frédéric; MOREAU-GAUDRY, Alexandre; BONNETERRE, Vincent; CINQUIN, Philippe; LANDELLE, Caroline; ccRICHAUD, Emmanuel (Elsevier, 2021)
    The need for personal protective equipment increased exponentially in response to the Covid-19 pandemic. To cope with the mask shortage during springtime 2020, a French consortium was created to find ways to reuse medical ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales