Laboratoire Mechanics, Surfaces and Materials Processing (MSMP): Soumissions récentes

Voici les éléments 176-182 de 421

    • On functional signatures of bare and coated formwork skin surfaces 
      Article dans une revue avec comité de lecture
      SPITZ, N.; MEZGHANI, Sabeur; ccEL MANSORI, Mohamed; ccCONIGLIO, Nicolas; ccMONTAGNE, Alex (Elsevier, 2018)
      The sticking of the concrete on metallic formworks during building construction generates many concrete wall defects. Several solutions have been proposed, among which surface lubrication and polymeric coatings are commonly ...
    • Cementite Residual Stress Analysis in Gas-nitrided Low Alloy Steels 
      Article dans une revue avec comité de lecture
      GOEKJIAN, S.; GUITTONNEAU, Fabrice; ccBARRALLIER, Laurent; ccJÉGOU, Sébastien (Materials Research Forum LLC, 2016)
      This paper deals with the measurement of residual stresses in cementite after gas-nitriding of a 33CrMoV12-9 steel. During nitriding, precipitation of nanometric alloying elements nitrides and cementite at grain boundaries ...
    • Investigations on the mechanical properties of the elementary thin films composing a CuIn1 − xGaxSe2 solar cell using the nanoindentation technique 
      Article dans une revue avec comité de lecture
      ABIB, Hocine; IOST, Alain; RAHMOUN, Khadidja; AYACHI, Boubakeur; VILCOT, Jean-Pierre; ccMONTAGNE, Alex (Elsevier, 2017)
      In this investigation, the mechanical properties of the different layers composing a CuIn1 − xGaxSe2 (CIGS) based solar cell were studied. Magnetron sputtering technique was used for the deposition of these layers except ...
    • A new method to fabricate Fe-TiC composite using conventional sintering and steam hammer 
      Article dans une revue avec comité de lecture
      LAHOUEL, Ali; BOUDEBANE, Saïd; IOST, Alain; ccMONTAGNE, Alex (Trans Tech Publications, 2017)
      The aim of this research paper is to fabricate a Fe-TiC composite by a novel and simple manufacturing method. The latter is based on two cumulative processes; a conventional sintering (transient liquid phase sintering) and ...
    • Sliding wear resistance of thermal sprayed wc-12co coatings reinforced with carbon nanotubes 
      Communication avec acte
      SANTANA, Y.Y.; GUTIÉRREZ, M.V.; STAIA, Mariana; LA BARBERA-SOSA, J.G.; PUCHI-CABRERA, Eli-Saul; IOST, Alain; CHICOT, Didier (Surface Modification Technologies (SMT31), 2017)
      Thermal sprayed coatings based on WC-Co are widely used for providing wear resistance to engineering components. The High Velocity Oxygen Fuel (HVOF) thermal spraying technique is one of the most commonly employed for ...
    • Investigations on the mechanical properties of the elementary thin films composing a CIGS solar cell using the nano indentation technique. 
      Article dans une revue avec comité de lecture
      ABIB, Hocine; IOST, Alain; RAHMOUN, Khadidja; VILCOT, Jean-Pierre; ccMONTAGNE, Alex (Elsevier, 2016)
      The aim of this work is to assess the mechanical properties of the different layers composing a CIGS based solar cell. Fabrication uses the magnetron sputtering deposition technique (except for the CdS layer which was ...
    • Friction and Wear Behavior of Ti-6Al-7Nb Biomaterial Alloy 
      Article dans une revue avec comité de lecture
      FELLAH, Mamoun; ASSALA, Omar; LABAIZ, Mohamed; DEKHIL, Leila; IOST, Alain (2013)
      The aim of this research is to study the tribological behaviour of AISI 316L stainless steel for surgical implants (total hip prosthesis). The tribological behaviour is evaluated by wear tests, using tribometers ball on ...