• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire des Matériaux et Procédés (LaBoMaP)
  • Voir le document
  • Accueil de SAM
  • Laboratoire des Matériaux et Procédés (LaBoMaP)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental study of locally loaded timber in compression perpendicular to the grain

Article dans une revue avec comité de lecture
Auteur
BLERON, Laurent
127742 Laboratoire Bourguignon des Matériaux et Procédés [LABOMAP]
DENAUD, Louis
127742 Laboratoire Bourguignon des Matériaux et Procédés [LABOMAP]
COLLET, Robert
127742 Laboratoire Bourguignon des Matériaux et Procédés [LABOMAP]
MARCHAL, Rémy
127742 Laboratoire Bourguignon des Matériaux et Procédés [LABOMAP]

URI
http://hdl.handle.net/10985/7398
Date
2011
Journal
European Journal of Environmental and Civil Engineering

Résumé

Since the test method for compression strength perpendicular to the grain was changed from a partial area to a full area loading test, strength values for softwood in EN 338 were significantly reduced. Consequently, a change in Eurocode 5 was necessary to ensure an equivalent resistance level in compression perpendicular to the grain. Experimental results are presented with wood in compression perpendicular to the grain. A numerical model is also presented. This model was used to establish a rule of calculation proposed at the P21A-Committee of the technical and construction equipment standardization office (BNTEC).

Fichier(s) constituant cette publication

Nom:
LABOMAP_EJECE_2011_BLERON.pdf
Taille:
808.2Ko
Format:
PDF
Description:
article principal
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire des Matériaux et Procédés (LaBoMaP)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • A Method of Lathe Checks Measurement; SMOF device and its software 
    Article dans une revue avec comité de lecture
    PAŁUBICKI, Bartosz; MARCHAL, Rémy; BUTAUD, Jean-Claude; DENAUD, Louis; BLERON, Laurent; COLLET, Robert; KOWALUK, Grzegorz (Springer Verlag, 2010)
    In the present paper, a novel method for veneer checks measurement and description based on digital image analysis is evaluated. According to this method, the camera is located sideways to the veneer allowing for viewing ...
  • Wood machining with a focus on French research in the last 50 years 
    Article dans une revue avec comité de lecture
    THIBAUT, Bernard; DENAUD, Louis; COLLET, Robert; MARCHAL, Rémy; BEAUCHENE, Jacques; MOTHE, Frédéric; MEAUSOONE, Pierre-Jean; MARTIN, Patrick; LARRICQ, Pierre; EYMA, Florent (Springer Nature (since 2011)/EDP Science (until 2010), 2016)
    Key message Wood machining is compulsory both for timber separation and the surfacing of wooden objects.The anisotropy, cellular nature and multi-scale level organisation of wood make its cutting complicated to study.During ...
  • Cutting Forces in basic and real life wood machining processes review, COST Action E35 2004-2008: Wood machining - Micromechanics and fracture 
    Article dans une revue avec comité de lecture
    MARCHAL, Rémy; MOTHE, Frédéric; DENAUD, Louis; THIBAUT, Bernard; BLERON, Laurent (De Gruyter, 2009)
    The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding ...
  • Online control of wood peeling process: acoustical and vibratory measurements of lathe checks frequency 
    Article dans une revue avec comité de lecture
    DENAUD, Louis; BLERON, Laurent; RATLE, Alain; MARCHAL, Rémy (Springer Nature (since 2011)/EDP Science (until 2010), 2007)
    In the course of most wood machining processes, operators are usually able to detect various problems simply by hearing the sound emitted by the process. This is especially true for wood peeling. Lathe checks formation has ...
  • Wood peeling process monitoring: a comparison of signal processing methods to estimate veneer average lathe check frequency 
    Article dans une revue avec comité de lecture
    DENAUD, Louis; BLERON, Laurent; EYMA, Florent; MARCHAL, Rémy (Springer Verlag, 2012)
    Experienced peeling operators are able to adjust the settings of their device by hearing the sound coming from the process. Based on this idea, a research program was undertaken to evaluate the possibility of using acoustic ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales