Reactive Gas Pulsing Process for Oxynitride Thin Films
Chapitre d'ouvrage scientifique
An original reactive sputtering method, namely the reactive gas pulsing process (RGPP) was developed for the synthesis of titanium oxynitride thin films. Such a method implements a metallic titanium target DC sputtered, a constant supply of argon and nitrogen gases and a pulsing oxygen mass flow rate, which is periodically controlled versus time. Various period times and different patterns can be generated: rectangle, sine, isosceles triangle, mounting or descending triangle and exponential. Real time measurements of the target potential as well as total sputtering pressure are recorded in order to study the instability phenomena of the process. They are also pertinent diagnostic tools to select the most suitable pulsing patterns required to alternate the process between the nitrided and the oxidized sputtering modes. As a result, alternation is produced for exponential and rectangular patterns. For this latter, the influence of the duty cycle α defined as the ratio of the injection time of oxygen by the pulsing period, on the behaviour of the reactive sputtering process and optical properties of deposited films, is systematically investigated. Finally, the added value brought by the exponential patterns is examined. It is shown that the exponential signal leads to significant improvements of the oxygen injection. The purpose is to introduce the right amount of oxygen so as to poison the titanium target surface without saturating the sputtering atmosphere by oxygen. Thus, the speed of pollution of the target surface appears as an appropriate parameter to better understand the beneficial effect of the exponential shape on the control of the RGPP method.
Fichier(s) constituant cette publication
Cette publication figure dans le(s) laboratoire(s) suivant(s)
Visualiser des documents liés par titre, auteur, créateur et sujet.
The contribution of grain boundary barriers to the electrical conductivity of titanium oxide thin films Article dans une revue avec comité de lectureMARTIN, Nicolas; BESNARD, Aurélien; STAHL, Fabrice; VAZ, Filipe; NOUVEAU, Corinne (American Institute of Physics, 2008)Titanium oxide thin films were prepared by reactive magnetron sputtering. The reactive gas pulsing process was implemented to control the oxygen injection in the deposition process and,consequently, to tune the oxygen ...
Article dans une revue avec comité de lectureBESNARD, Aurélien; MARTIN, Nicolas; STAHL, Nicolas; CARPENTIER, Luc; RAUCH, Jean-Yves (World Scientific, 2013)Titanium thin films were deposited by DC magnetron sputtering. The glancing angle deposition (GLAD) method was implemented to prepare two series of titanium films: perpendicular and oriented columnar structures. The first ...
Accurate control of friction with nanosculptured thin coatings: Application to gripping in microscale assembly Article dans une revue avec comité de lectureSTEMPFLE, Philippe; BESNARD, Aurélien; MARTIN, Nicolas; DOMATTI, Anne; TAKADOUM, Jamal (Elsevier, 2013)Chromium thin films were sputter deposited implementing the GLancing Angle Deposition (GLAD) method, which is a thin film deposition technique where the incident vapor flux – composed of atoms and molecules from gas phase ...
Article dans une revue avec comité de lectureZAIRI, Amel; NOUVEAU, Corinne; LARBI, Ahmed Beb Cheikh; IOST, Alain; MARTIN, Nicolas; BESNARD, Aurélien (Maney Publishing, 2014)CrSiN films were deposited by reactive radio frequency magnetron sputtering in an Ar+N2 gas mixture. The nitrogen gas was injected in the deposition chamber using two methods: the classical constant injection and pulsed ...
Study of the influence of the pressure and rotational motion of 3D substrates processed by magnetron sputtering: A comparative study between Monte Carlo modelling and experiments Article dans une revue avec comité de lectureEVRARD, Martin; BESNARD, Aurélien; LUCAS, Stephane (Elsevier, 2019)Over the last ten years, low pressure plasma solutions for materials surface treatment have been remarkable. Nevertheless, the deposition of films with a uniform thickness on 3D complex shapes is still a challenge for ...