• français
    • English
    français
  • Login
Help
View Item 
  •   Home
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • View Item
  • Home
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental study of the impact of punching operations on the high cycle fatigue strength of Fe-Si thin sheets

Article dans une revue avec comité de lecture
Author
DEHMANI, Helmi
206863 Laboratoire des Arts et Métiers ParisTech d'Angers - Procédés Matériaux Durabilité [LAMPA - PMD]
164351 Institut de Mécanique et d'Ingénierie de Bordeaux [I2M]
BRUGGER, Charles
164351 Institut de Mécanique et d'Ingénierie de Bordeaux [I2M]
PALIN-LUC, Thierry
164351 Institut de Mécanique et d'Ingénierie de Bordeaux [I2M]
MAREAU, Charles
206863 Laboratoire des Arts et Métiers ParisTech d'Angers - Procédés Matériaux Durabilité [LAMPA - PMD]
KOECHLIN, Samuel
467842 Emerson-Leroy Somer

URI
http://hdl.handle.net/10985/10762
DOI
10.1016/j.ijfatigue.2015.09.030
Date
2016
Journal
International Journal of Fatigue

Abstract

In this paper, the impact of punching operations on the high cycle fatigue strength of Fe–Si thin sheets is investigated. High cycle fatigue tests are performed on both punched and polished edge specimens. Results show a significant decrease of the fatigue strength in the case of punched specimens. Different factors are found to be responsible for this degradation. First, according to SEM observations of fracture surfaces and to 3D surface topography, fatigue crack initiation is strongly governed by the geometrical defects resulting from punching operations. Second, important tensile residual stresses, which are analyzed using X-ray diffraction techniques, are observed on punched edges. Depending on the loading conditions, it is possible for the residual stress field to be redistributed as a result of cyclic plasticity. Third, punching operations are responsible for the introduction of a plastically hardened zone which, according to both micro-hardness measurements and diffraction data, is about 200 µm deep. Based upon this experimental dataset, the parameters of the Murakami criterion are identified. This criterion is found to provide a reasonable description of the experimental results when the residual stresses around punched edges are accounted for.

Files in this item

Name:
LAMPA-pmd_IJF_Dehmani_2016.pdf
Size:
3.186Mb
Format:
PDF
Embargoed until:
2018-01-31
View/Open

Collections

  • Institut de Mécanique et d’Ingénierie de Bordeaux (I2M)
  • Laboratoire Angevin de Mécanique, Procédés et InnovAtion (LAMPA)

Related items

Showing items related by title, author, creator and subject.

  • High Cycle Fatigue Strength of Punched Thin Fe-Si Steel Sheets 
    Article dans une revue avec comité de lecture
    DEHMANI, Helmi; BRUGGER, Charles; PALIN-LUC, Thierry; MAREAU, Charles; KOECHLIN, Samuel (2016)
    Some parts of electrical machines are built from stacks of thin steel sheets, for which the coarse grain microstructure allows for minimizing magnetic losses. The fabrication process of these parts usually involves punching ...
  • Study of the contribution of different effects induced by the punching process on the high cycle fatigue strength of the M330-35A electrical steel 
    Article dans une revue avec comité de lecture
    DEHMANI, Helmi; BRUGGER, Charles; PALIN-LUC, Thierry; MAREAU, Charles; KOECHLIN, Samuel (ESIS - Elsevier, 2016)
    Because of their improved magnetic properties, Fe-Si alloys are widely used for new electric motor generations. The use of punching process to obtain these components specially affects their mechanical behavior and fatigue ...
  • High cycle fatigue strength assessment methodology considering punching effects 
    Article dans une revue avec comité de lecture
    DEHMANI, Helmi; BRUGGER, Charles; PALIN-LUC, Thierry; MAREAU, Charles; KOECHLIN, Samuel (Elsevier, 2018)
    Since a decrease of the fatigue strength may result from punching operations, this study proposes a methodology for designing punched parts against high cycle fatigue crack initiation. To reach this goal, high cycle fatigue ...
  • Characterization and simulation of the effect of punching on the high cycle fatigue strength of thin electric steel sheets 
    Article dans une revue avec comité de lecture
    DEHMANI, Helmi; BRUGGER, Charles; PALIN-LUC, Thierry; MAREAU, Charles; KOECHLIN, Samuel (Elsevier, 2015)
    Rotors of electric machines are built from stacks of thin steel sheets. The fabrication process of these components usually involves punching operations that generate defects on the steel sheet edges. In this study, high ...
  • Ultrasonic fatigue testing device under biaxial bending 
    Article dans une revue avec comité de lecture
    BRUGGER, Charles; PALIN-LUC, Thierry; OSMOND, Pierre; BLANC, Michel (Università di Cassino, 2016)
    A new fatigue testing device has been developed to test specimens under biaxial loading at 20 kHz. A flat smooth specimen with a disc geometry is placed on a torus frame and cyclically loaded at the center of its upper ...

Browse

All SAMCommunities & CollectionsAuthorsIssue DateCenter / InstitutionThis CollectionAuthorsIssue DateCenter / Institution

Newsletter

Latest newsletterPrevious newsletters

Statistics

Most Popular ItemsStatistics by CountryMost Popular Authors

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales