Laboratoire des Matériaux et Procédés (LaBoMaP): Soumissions récentes

Voici les éléments 43-49 de 370

    • Specific cutting coefficients for the most common engineered wood products 
      Communication avec acte
      ccGOLI, Giacomo; CURTI, Rémi; TODARO, Luigi; MARCON, Bertrand (2023-10-04)
      The aim of the present work is to investigate the specific cutting coefficients for the assessment of cutting forces when peripheral milling different types of engineered wood products (EWPs). The approach comes from ...
    • Influence of Sahelian and Sudanian provenances on the physical and mechanical properties of Faidherbia albida wood from Chad 
      Article dans une revue avec comité de lecture
      ccDOUGABKA, Dao; ccGERARD, Jean; BIANZEUBE, Tikri; ccMARCHAL, Rémy; GUIBAL, Daniel; GUYOT, Alban (Informa UK Limited, 2021-05-18)
      Faidherbia albida is a typical emblematic species of African dryland areas. In Chad, it is used for many purposes, but very little is known about the technological properties of its wood, which sometimes leads to inappropriate ...
    • Ta2C precipitation after low pressure carburizing of tantalum 
      Article dans une revue avec comité de lecture
      ccCOTTON, Dominique; JACQUET, Philippe; FAURE, Sébastien; VIGNAL, Vincent (Elsevier, 2022)
      Low pressure carburizing cycles were carried out on tantalum samples. A Ta2C precipitates layer is present under the TaC and Ta2C surface layers. As the TaC and Ta2C layers, the Ta2C precipitates layer (TPL) grows by ...
    • Effect of Bilayer Variation on the Properties of CrN/CrAlN Multilayer Coatings Produced by DC Magnetron Sputtering 
      Communication avec acte
      BESNARD, Aurélien; NOUVEAU, Corinne; ccMONTAGNE, Alex; TLILI, B.; NAAMANE, S.; AOUADI, Khalil (Springer Nature Switzerland, 2023-09-13)
      In this study, CrN/CrAlN multilayer coating with different periods (Ʌ = 1, 2, 3, 4) were deposited on stainless steel (90CrMoV8) and silicon Si (100) samples by DC magnetron sputtering. The results obtained exhibited ...
    • An image processing method to recognize position of sawn boards within the log 
      Article dans une revue avec comité de lecture
      LI, Xiaolin; ccPOT, Guillaume; NGO, Phuc; ccVIGUIER, Joffrey; ccPENVERN, Hélène (Springer Science and Business Media LLC, 2023-09-13)
      This paper addresses the problem of timber board positioning within the log where they were sawn from. The method takes as input log and board end cross-section images. It uses a two-step image matching method based on ...
    • DETERMINATION OF LIGHT TRANSMITTANCE IN FRENCH LOCAL TREE SPECIES 
      Communication avec acte
      ccBOIVIN, Juliette; DENAUD, Louis; GIRARDON, Stéphane; TEYSSIEUX, Damien; ccFROEHLY, Luc (ICEM20, 2023-07-02)
      Wood is a multi-structural material with properties depending on its growing conditions. This variability is considered in industry through different non-destructive testing methods. Among them, the use of lasers to detect ...
    • Synthesis and tribocorrosion performances of multilayer (Ta/ZrN)n coatings 
      Article dans une revue avec comité de lecture
      ccNASSER EDDINE, BELIARDOUH; RAMOUL, Chems Eddine; NOUVEAU, Corinne; ccKALELI, Emrullah Hakan; ccMONTAGNE, Alex (Elsevier BV, 2022-03-19)
      Multilayer thin coatings (~3 µm in thickness) were deposited using reactive radio frequency magnetron sputtering on Ti-6Al-4 V substrate for biomaterial applications. Films are a combination of hard zirconium nitride with ...