Laboratoire Procédés et Ingénierie en Mécanique et Matériaux (PIMM): Soumissions récentes

Voici les éléments 687-693 de 1243

    • Thermal cycling of cold-pressed PTFE compacts: Reversible and irreversible behavior 
      Article dans une revue avec comité de lecture
      GUENOUN, Gabriel; FAOU, Jean-Yvon; SCHMITT, Nicolas; ccREGNIER, Gilles (Elsevier, 2019)
      Cold uniaxial pressed PTFE compacts were subjected to thermal cycles of increasing maximum temperature below melting temperature, and thermal expansion was followed in both the compaction and transverse directions. The ...
    • Particularities of multi-cutter cutting dynamics 
      Article dans une revue avec comité de lecture
      GOUSKOV, Alexander; PANOVKO, Grigory; SHOKHIN, Alexander E.; KALIMOLDAYEV, Maksat N.; UALIYEV, Zair Gakhipovich; ccGUSKOV, Mikhail (National Academy of Sciences of the Republic of Kazakhstan, 2019)
      Certain particularities of steady continuous cutting dynamics for multi-cutter turning and the results of mathematical modeling are discussed in the paper. The effect of processing parameters on the excitation of vibration ...
    • RLCYC 75: A 2 kW electrically calibrated laser calorimeter designed for Laser MegaJoule diagnostics calibration 
      Article dans une revue avec comité de lecture
      VILLATE, Denis; SOSCIA, M.; COSTE, Frédéric; ANDRÉ, R. (IOP Publishing, 2013)
      RLCYC 75 is a new electrically calibrated laser calorimeter specially manufactured by Laser Metrology to calibrate energy diagnostics within the Laser MegaJoule (LMJ) facility. It consists of an optical cavity cooled by a ...
    • Influence of the microstructure and laser shock processing (LSP) on the corrosion behaviour of the AA2050-T8 aluminium alloy 
      Article dans une revue avec comité de lecture
      AMAR, Hassan; KRAWIEC, Halina; JOSSE, Claudie; PEYRE, Patrice; DA SILVA, S. N.; DICK, Luis Federico (Elsevier, 2011)
      The corrosion behaviour of AA2050-T8 was studied after polishing and after laser shock processing (LSP) treatment using the electrochemical microcell technique and the SVET. After polishing, pitting at constituent particles ...
    • Multireflection grazing incidence diffraction used for stress measurementsin surface layers 
      Article dans une revue avec comité de lecture
      MARCISZKO, M; WROBEL, M; SEILER, W; DONGES, J; SNIECHOWSKI, M; WIERZBANOWSKIA, K; BACZMANSKI, Andrzej; ccBRAHAM, Chedly (Elsevier, 2013)
      The geometry based on the multireflection grazing incidence X-ray diffraction can be applied to measure residual stresses. Using this method, it is possible to perform a non-destructive analysis of the heterogeneous stresses ...
    • Optimal dual-PZT sizing and network design for baseline-free SHM of complex anisotropic composite structures 
      Article dans une revue avec comité de lecture
      LIZÉ, Emmanuel; BOLZMACHER, Christian; ccMECHBAL, Nazih; ccRÉBILLAT, Marc (IOP Publishing, 2018)
      Structural health monitoring (SHM) processes for aeronautic composite structures are generally based on the comparison of healthy and unknown databases. The need for prior baseline signals is one of the barriers to industrial ...
    • Reducing the Gap between the Activation Energy Measured in the Liquid and the Glassy States by Adding a Plasticizer to Polylactide 
      Article dans une revue avec comité de lecture
      ARAUJO, Steven; DELPOUVE, Nicolas; DHÔTEL, Alexandre; DOMENEK, Sandra; GUINAULT, Alain; DELBREILH, Laurent; DARGENT, Eric (ACS Publications, 2018)
      The kinetic fragility of a glass-forming liquid is an important parameter to describe its molecular mobility. In most polymers, the kinetic fragility index obtained from the glassy state by thermally stimulated depolarization ...