• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • Voir le document
  • Accueil de SAM
  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Numerical and analytical modeling of orthogonal cutting : The link between local variables and global contact characteristics

Article dans une revue avec comité de lecture
Auteur
MOLINARI, Alain
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
CHERIGUENE, Rachid
178323 Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
MIGUELEZ, Henar

URI
http://hdl.handle.net/10985/6556
DOI
10.1016/j.ijmecsci.2010.12.007
Date
2011

Résumé

The response of the tool–chip interface is characterized in the orthogonal cutting process by numerical and analytical means and compared to experimental results. We study the link between local parameters (chip temperature, sliding friction coefficient, tool geometry) and overall friction characteristics depicting the global response of the tool–chip interface. Sticking and sliding contact regimes are described. The overall friction characteristics of the tool are represented by two quantities: (i) the mean friction coefficient qualifies the global response of the tool rake face (tool edge excluded) and (ii) the apparent friction coefficient reflects the overall response of the entire tool face, the effect of the edge radius being included. When sticking contact is dominant the mean friction coefficient is shown to be essentially the ratio of the average shear flow stress along the sticking zone by the average normal stress along the contact zone. The dependence of overall friction characteristics is analyzed with respect to tool geometry and cutting conditions. The differences between mean friction and apparent friction are quantified. It is demonstrated that the evolutions of the apparent and of the mean friction coefficients are essentially controlled by thermal effects. Constitutive relationships are proposed which depict the overall friction characteristics as functions of the maximum chip temperature along the rake face. This approach offers a simple way for describing the effect of cutting conditions on the tool–chip interface response. Finally, the contact length and contact forces are analyzed. Throughout the paper, the consistency between numerical, analytical and experimental results is systematically checked.

Fichier(s) constituant cette publication

Nom:
numerical_IJMS_2011_ps.pdf
Taille:
2.041Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Application des séries de Volterra non entière à l'identification de systèmes thermiques en conditions extrêmes 
    Communication avec acte
    MAACHOU, Asma; MALTI, Rachid; MELCHIOR, Pierre; ccBATTAGLIA, Jean-Luc; OUSTALOUP, Alain; HAY, Bruno (Société Française de Thermique / Congrès Français de Thermique - Thermique en conditions extrêmes, 29 mai - 1er juin 2012, Bordeaux, 2012)
    Les modèles linéaires non entiers ont prouvé leur efficacité dans la modélisation de phénomènes de diffusion thermique pour de faibles variations de température. Cependant, pour de larges variations de température, comme ...
  • Tool life and surface integrity in hard milling of hot work tool steels 
    Communication avec acte
    M'SAOUBI, Rachid; CHANDRASEKARAN, H.; COULON, Bertrand; MARQUES, M.J.; MARTINS DO OUTEIRO, Jose Carlos (2008)
    Machinability enhancement of hot work tool steels can be achieved intrinsically through tailoring of alloying elements and steel processing route but also externally through the use of adequate tooling. The aim of the ...
  • Evaluation of present numerical models for predicting metal cutting performance ans residual stresses 
    Article dans une revue avec comité de lecture
    UMBRELLO, Domenico; M'SAOUBI, Rachid; JAWAHIR, I.S.; MARTINS DO OUTEIRO, Jose Carlos (Taylor & Francis, 2015)
    Efforts on numerical modeling and simulation of metal cutting operations continue to increase due to the growing need for predicting the machining performance. A significant number of numer- ical methods, especially the ...
  • Tool wear monitoring and hole surface quality during CFRP drilling 
    Communication avec acte
    RAMIREZ, Christophe; POULACHON, Gerard; ROSSI, Frederic; M'SAOUBI, Rachid (Elsevier, 2014)
    The present investigation focuses on the evaluation of tool wear and surface integrity in the context of CFRP cutting. Series of drilling experiments were performed on CFRP plates using cemented carbide solid drills with ...
  • Identification of Model Parameter for the Simulation of SMA Structures Using Full Field Measurements 
    Conférence invitée
    CHEMISKY, Yves; ccMERAGHNI, Fodil; BOURGEOIS, Nadine; CORNELL, Stephen; ECHCHORFI, Rachid; PATOOR, Etienne (Ibrahim Karaman, Raymundo Arróyave and Eyad Masad/ Wiley, 2015)
    With the design of new devices with complex geometry and to take advantage of their large recoverable strains, shape memory alloys components (SMA) are increasingly subjected to multiaxial loadings. The development process ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales