Low friction MoS2TiW Coatings Manufactured on X38CrMoV5-1 Steel Using PVD Method
Article dans une revue avec comité de lecture
In this article the friction coefficients and the wear resistances of MoS2TiW protective coatings manufactured on X38CrMoV5-1 steel samples by using PVD technology are studied. The investi- gations based on tribometer tests which were carried out in different temperature conditions. The process of deposition of PVD coatings was realized by using multisource, hybrid factory- scale equipment of type URM 079. This equipment allows for deposition of coatings by the phys- ical method. The tribological tests were performed using a precision high temperature tribome- ter under ambient and high temperature conditions with a steel and corundum balls as coun- ter-samples. In this paper the results of these tribological tests are presented. It is shown that the measured friction coefficient of steel samples with PVD coatings is significantly lower than the friction coefficient of uncoated steel. It is also shown that X38CrMoV5-1 steel samples with manufactured MoS2TiW coatings are characterized by very low friction coefficient and high wear resistance.
Showing items related by title, author, creator and subject.
Tribological investigations of TiC+a-C:H Coatings Manufactured on X38CrMoV5-1 Steel Using PVD Technology Article dans une revue avec comité de lectureGOLABCZAK, Marcin; JACQUET, Philippe; NOUVEAU, Corinne; FLITI, Romain (Trans Tech Publications, 2013)X38CrMoV5-1 steel is a typical tool steel commonly used in forging and plastic moulding industry for production of ejectors, slides, dies, etc. In plastics moulding a lot of these parts sustain relative movement. Because ...
Investigations of geometrical structure and morphology of samples made of hard machinable materials after wire electrical discharge machining and vibro‐abrasive finishing Article dans une revue avec comité de lectureGOŁĄBCZAK, M.; MAKSIM, P.; JACQUET, Philippe; GOŁĄBCZAK, A.; WOŹNIAK, K.; NOUVEAU, Corinne (Wiley-VCH Verlag, 2019)In this article the results concerned influence of processing conditions of the wire electrical discharge machining and vibro‐abrasive machining on the surface layer and morphology of samples made of hard machinable materials ...
Investigations of surface layer temperature and morphology of hard machinable materials used in aircraft industry during abrasive electrodischarge grinding process Article dans une revue avec comité de lectureGOŁĄBCZAK, M.; ŚWIĘCIK, R.; GOŁĄBCZAK, A.; NOUVEAU, Corinne; JACQUET, Philippe; BLANC, C. (Wiley-VCH Verlag, 2018)In this work the results related to the influence of selected electrical parameters of the abrasive electrodischarge grinding process on the surface layer temperature and morphology of machined samples in comparison to the ...
A study of the wear performance of duplex treated commercial low-alloy steel against alumina and WC balls Article dans une revue avec comité de lectureBELIARDOUH, Nasser Eddine; NOUVEAU, Corinne; WALOCK, Michael J.; JACQUET, Philippe (Elsevier, 2014)The objective of this work is to study the improvement of the tribological properties of low alloy steel using a duplex treatment of lowpressure carburizing and the deposition of a Cr–(WC–Co) coating by dual RF magnetron ...
Article dans une revue avec comité de lectureSIAD, Ahcene; NOUVEAU, Corinne; BESNARD, Aurélien; JACQUET, Philippe; QUESADA, Jean (Lavoisier, 2015)The objective of this study is to determine the influence of duplex treatment (low pressure thermochemical treatment and PVD coating) on tribological properties. The carbide and carbonitride coatings are deposited by dual ...