Nos laboratoires: Soumissions récentes

Voici les éléments 3529-3535 de 6547

    • Comparative analysis of procedures for the estimation of uncertainties in LCA: clay brick case study 
      Article dans une revue avec comité de lecture
      SILVA, Fernanda Belezario; YOSHIDA, Olga Satomi; HORTA ARDUIN, Rachel; VINHAL, Lais D; TEIXEIRA, Claudia Echevenga; OLIVEIRA, Luciana A (2017)
      O presente trabalho tem como objetivo discutir a estimativa de incertezas em ACV, utilizando três procedimentos de cálculo a partir de dados de inventários da produção de blocos cerâmicos de uma fábrica localizada no Estado ...
    • Existence of a Critical Layer Thickness in PS/PMMA Nanolayered Films 
      Article dans une revue avec comité de lecture
      BIRONEAU, Adrien; SALEZ, Thomas; MIQUELARD-GARNIER, Guillaume; SOLLOGOUB, Cyrille (American Chemical Society, 2017)
      An experimental study was carried out to investigate the existence of a critical layer thickness in nanolayer coextrusion, under which no continuous layer is observed. Polymer films containing thousands of layers of ...
    • Successive bifurcations in a fully three-dimensional open cavity flow 
      Article dans une revue avec comité de lecture
      PICELLA, Francesco; LUSSEYRAN, F; CHERUBINI, Stefania; PASTUR, L; ccROBINET, Jean-Christophe; ccLOISEAU, Jean-Christophe (Cambridge University Press (CUP), 2018)
      The transition to unsteadiness of a three-dimensional open cavity flow is investigated using the joint application of direct numerical simulations and fully three-dimensional linear stability analyses, providing a clear ...
    • A bi-harmonic five-phase SPM machine with low ripple torque for marine propulsion 
      article dans une revue avec comité de lecture
      ZAHR, Hussein; ccSEMAIL, Eric; ccSCUILLER, Franck (2017)
      This paper addresses the design of a bi-harmonic five-phase Surface-mounted Permanent Magnet (SPM) machine for marine propulsion. The bi-harmonic characteristic results from the particular 20 slots-8 poles configuration ...
    • Multi-view VR system for co-located multidisciplinary collaboration and its application in ergonomic design 
      Communication avec acte
      LI, Bo; ccLOU, Ruding; POSSELT, Javier; ccSEGONDS, Frederic; ccMERIENNE, Frédéric; KEMENY, Andras (2017)
      In co-located collaborative environment for product design, new groupware of multi-view system allows multiple experts to have individual visual information. A co-located multi-view VR system and a multidisciplinary task ...
    • Adaptation of life-cycle inventories of sawn timber used in the structure of roofs in the state of São Paulo 
      Article dans une revue avec comité de lecture
      SOUZA, Carolina A; PIGOZZO, Raphael J. B.; SILVA, Fernanda B; HORTA ARDUIN, Rachel; OLIVEIRA, Luciana A; TEIXEIRA, Claudia Echevenga (2017)
      Este trabalho teve como objetivo desenvolver o inventário de ciclo de vida para madeira empregada na estrutura de telhado de edificações populares do Estado de São Paulo, com base na adaptação de inventários existentes na ...
    • Nanocolumnar TiN thin film growth by oblique angle sputter-deposition: Experiments vs. simulations 
      Article dans une revue avec comité de lecture
      BOUAOUINA, Boudjemaa; MASTAIL, Cédric; ccBESNARD, Aurélien; MAREUS, Rubenson; NITA, Florin; MICHEL, Anny; ABADIAS, Grégory (Elsevier, 2018)
      Nanostructured columnar titanium nitride (TiN) thin films were produced by oblique angle deposition using reactive magnetron sputtering. The influence of the angular distribution of the incoming particle flux on the resulting ...