Laboratoire des Matériaux et Procédés (LaBoMaP): Soumissions récentes

Voici les éléments 288-294 de 382

    • Effect of layer thickness on thermal properties of multilayer thin films produced by PVD 
      Article dans une revue avec comité de lecture
      TLILI, Brahim; WALOCK, Michael J.; NASRI, Mustapha; GHRIB, Taher; ccNOUVEAU, Corinne (Elsevier, 2012)
      Cr/CrN/CrAlN, CrN/CrAlN and Cr/CrN thin layers were deposited by PVD (Physical Vapor Deposition). The multilayers were obtained from the combined deposition of different layers Cr, CrN and CrAlN thick films on on AISI4140 ...
    • Analysis of chip formation mechanisms and modelling of slabber process 
      Article dans une revue avec comité de lecture
      PFEIFFER, Renaud; ccCOLLET, Robert; ccDENAUD, Louis; ccFROMENTIN, Guillaume (Springer Verlag, 2014)
      During the primary transformation in wood industry, logs are faced with conical rough milling cutters commonly named slabber or canter heads. Chips produced consist of raw materials for pulp paper and particleboard industries. ...
    • Pre-evaluation on surface profile in turning process based on cutting parameters 
      Article dans une revue avec comité de lecture
      LU, Chen; MA, Ning; CHEN, Zhuo; COSTES, Jean-Philippe (Springer Verlag, 2009)
      Traditional online or in-process surface profile (quality) evaluation (prediction) needs to integrate cutting parameters and several in-process factors (vibration, machine dynamics, tool wear, etc) for high accuracy. However ...
    • Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC copper 
      Communication avec acte
      DENGUIR, Lamice; ccFROMENTIN, Guillaume; ccMARTINS DO OUTEIRO, Jose Carlos; VIGNAL, Vincent; BESNARD, Rémy (ELSEVIER, 2014)
      Superfinishing machining has a particular impact on cutting mechanics, surface integrity and local electrochemical behavior. In fact, material removal during this process induces geometrical, mechanical and micro-structural ...
    • Tool Wear Effect on Cutting Forces: In Routing process of Aleppo Pine Wood 
      Article dans une revue avec comité de lecture
      AKNOUCHE, Hamid; OUTAHYON, Alex; MARCHAL, Rémy; ZERIZER, Abdellatif; BUTAUD, Jean-Claude; ccNOUVEAU, Corinne (Elsevier, 2009)
      This paper uses the cutting forces in a routing process of Aleppo pine wood to estimate the tool wear effect. The aim is to obtain further information about the tool wear effect by monitoring the variation in the cutting ...
    • Effect of RGPP process on properties of Cr–Si–N coatings 
      Article dans une revue avec comité de lecture
      ZAIRI, Amel; ccNOUVEAU, Corinne; ccBEN CHEIKH LARBI, Ahmed; IOST, Alain; MARTIN, Nicolas; ccBESNARD, Aurélien (Maney Publishing, 2014)
      CrSiN films were deposited by reactive radio frequency magnetron sputtering in an Ar+N2 gas mixture. The nitrogen gas was injected in the deposition chamber using two methods: the classical constant injection and pulsed ...
    • Prediction of the Spindle and Tool Receptance : Industrial Application in Reaming Process 
      Communication avec acte
      SELMI, Jaouher; SELMI, Jaouher; COSTES, Jean-Philippe; COSTES, Jean-Philippe; ccLORONG, Philippe; ccLORONG, Philippe; ccPOULACHON, Gerard; ccPOULACHON, Gerard; CARRAS, Patrice; CARRAS, Patrice (MM Science JournalMM Science Journal, 2014)
      It is proposed to apply a methodology in order to evaluate the ability of different machining systems (Spindle/Tool) to run a reaming process in a stable way.The methodology is based on an experimental measurement of the ...