• français
    • English
    English
  • Ouvrir une session
Aide
Voir le document 
  •   Accueil de SAM
  • Laboratoire des Matériaux et Procédés (LaBoMaP)
  • Voir le document
  • Accueil de SAM
  • Laboratoire des Matériaux et Procédés (LaBoMaP)
  • Voir le document
JavaScript is disabled for your browser. Some features of this site may not work without it.

Effect of Ar/N2 flow ratio on the microstructure and mechanical properties of Ti-Cr-N coatings deposited by DC magnetron sputtering on AISI D2 tool steels

Article dans une revue avec comité de lecture
Auteur
KEHAL, Abdelkrim
252490 Université Mouloud Mammeri [Tizi Ouzou] = Mouloud Mammeri University of Tizi-Ouzou [UMMTO]
230815 Unité de Recherche Matériaux, Procédés et Environement - URMPE (Boumerdès, Algérie)
SAOULA, Nadia
42013 Centre de Développement des Technologies Avancées [CDTA]
ABAIDIA, Seddik El Hak
230815 Unité de Recherche Matériaux, Procédés et Environement - URMPE (Boumerdès, Algérie)
NOUVEAU, Corinne
127742 Laboratoire Bourguignon des Matériaux et Procédés [LABOMAP]

URI
http://hdl.handle.net/10985/20797
DOI
10.1016/j.surfcoat.2021.127444
Date
2021
Journal
Surface & Coatings Technology

Résumé

Ti-Cr-N coatings were deposited on Si (100) and AISI D2 tool steel substrates by reactive DC magnetron co- sputtering technique from titanium and chromium target in mixed Ar/N2 atmosphere. The Ar/N2 ratio effects on the chemical composition, structure, morphology, intrinsic stress and mechanical properties of the Ti-Cr-N coatings were investigated. The growing process of Ti-Cr-N coatings can be divided into three stages: Stage I, in poisoning mode (low flow ratio 1 < Ar/N2 ≤1.4), Stage II, in transition mode (intermediate flow ratio 1.4 ≤Ar/N2 ≤ 3) and Stage III in metallic mode (Ar/N2 > 3). For all samples, XRD analysis shown the formation of mixed nitrides phases. In stage I, Ti2N, TiN0.3, and hexagonal-Cr2N phases were observed. In Stage II, TiN0.3, Cr2N, and cubic-TiN phases were formed, while only TiN and Cr2N are observed in stage III. The coatings deposited with Ar/N₂ ratio of 3 shows the largest hardness of 24 GPa which is attribute to the dense structure and smoother surface morphology. The properties of the films are discussed in terms of evolution growth stages resulting by the variation of Ar/N2 flow ratios.

Fichier(s) constituant cette publication

Nom:
LaBoMaP_SCT_2021_NOUVEAU.pdf
Taille:
4.551Mo
Format:
PDF
Voir/Ouvrir

Cette publication figure dans le(s) laboratoire(s) suivant(s)

  • Laboratoire des Matériaux et Procédés (LaBoMaP)

Documents liés

Visualiser des documents liés par titre, auteur, créateur et sujet.

  • Residual stress, mechanical and microstructure properties of multilayer Mo2N/CrN coating produced by R.F Magnetron discharge 
    Article dans une revue avec comité de lecture
    BOUAOUINA, Boudjemaa; BESNARD, Aurélien; ABAIDIA, Seddik El Hak; HAID, F. (Elsevier, 2017)
    We have investigated the effect of the period thickness of the multilayer Mo2N/CrN deposited on Si substrate produced by reactive magnetron sputtering. Mo2N presents a face centered cubic structure and CrN an orthorhombic ...
  • Correlation between mechanical and microstructural properties of molybdenum nitride thin films deposited on silicon by reactive RF magnetron discharge 
    Article dans une revue avec comité de lecture
    BOUAOUINA, Boudjemaa; BESNARD, Aurélien; ABAIDIA, Seddik El Hak; AIROUDJ, Aissam; BENSOUICI, Fayçal (Elsevier, 2018)
    Molybdenum nitride thin films were deposited on (100) silicon substrates by R.F. magnetron sputtering of a Mo target in a (Ar-N2) gas mixtures. The films were studied by Scanning Electron Microscopy (SEM), Energy Dispersive ...
  • Recirculating Flows Involving Short Fiber Suspensions: Numerical Difficulties and Efficient Advanced Micro-Macro Solvers 
    Article dans une revue avec comité de lecture
    EL KISSI, Nadia; ccPRULIERE, Etienne; ccAMMAR, Amine; ccCHINESTA SORIA, Francisco (Springer Link, 2009)
    Numerical modelling of non-Newtonian flows usually involves the coupling between equations of motion characterized by an elliptic character, and the fluid constitutive equation, which defines an advection problem linked ...
  • Effect of layer thickness on thermal properties of multilayer thin films produced by PVD 
    Article dans une revue avec comité de lecture
    TLILI, Brahim; WALOCK, Michael J.; NASRI, Mustapha; GHRIB, Taher; NOUVEAU, Corinne (Elsevier, 2012)
    Cr/CrN/CrAlN, CrN/CrAlN and Cr/CrN thin layers were deposited by PVD (Physical Vapor Deposition). The multilayers were obtained from the combined deposition of different layers Cr, CrN and CrAlN thick films on on AISI4140 ...
  • Tribological investigations of TiC+a-C:H Coatings Manufactured on X38CrMoV5-1 Steel Using PVD Technology 
    Article dans une revue avec comité de lecture
    ccGOŁĄBCZAK, Marcin; JACQUET, Philippe; NOUVEAU, Corinne; FLITI, Romain (Trans Tech Publications, 2013)
    X38CrMoV5-1 steel is a typical tool steel commonly used in forging and plastic moulding industry for production of ejectors, slides, dies, etc. In plastics moulding a lot of these parts sustain relative movement. Because ...

Parcourir

Tout SAMLaboratoiresAuteursDates de publicationCampus/InstitutsCe LaboratoireAuteursDates de publicationCampus/Instituts

Lettre Diffuser la Science

Dernière lettreVoir plus

Statistiques de consultation

Publications les plus consultéesStatistiques par paysAuteurs les plus consultés

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales

ÉCOLE NATIONALE SUPERIEURE D'ARTS ET METIERS

  • Contact
  • Mentions légales