Modelling and Optimization of Machining of Ti-6Al-4V Titanium Alloy Using Machine Learning and Design of Experiments Methods
Article dans une revue avec comité de lecture
Ti-6Al-4V titanium is considered a difficult-to-cut material used in critical applications in the aerospace industry requiring high reliability levels. An appropriate selection of cutting conditions can improve the machinability of this alloy and the surface integrity of the machined surface, including the generation of compressive residual stresses. In this paper, orthogonal cutting tests of Ti-6Al-4V titanium were performed using coated and uncoated tungsten carbide tools. Suitable design of experiments (DOE) was used to investigate the influence of the cutting conditions (cutting speed Vc, uncut chip thickness h, tool rake angle γn, and the cutting edge radius rn) on the forces, chip compression ratio, and residual stresses. Due to the time consumed and the high cost of the residual stress measurements, they were only measured for selected cutting conditions of the DOE. Then, the machine learning method based on mathematical regression analysis was applied to predict the residual stresses for other cutting conditions of the DOE. Finally, the optimal cutting conditions that minimize the machining outcomes were determined. The results showed that when increasing the compressive residual stresses at the machined surface by 40%, the rake angle should be increased from negative (−6°) to positive (5°), the cutting edge radius should be doubled (from 16 µm to 30 µm), and the cutting speed should be reduced by 67% (from 60 to 20 m/min).
Fichier(s) constituant cette publication
Cette publication figure dans le(s) laboratoire(s) suivant(s)
Visualiser des documents liés par titre, auteur, créateur et sujet.
Constitutive model incorporating the strain-rate and state of stress effects for machining simulation of titanium alloy Ti6Al4V Communication avec acteCHENG, Wenyu; OUTEIRO, José; COSTES, Jean-Philippe; M’SAOUBI, Rachid; KARAOUNI, Habib; DENGUIR, Lamice; ASTAKHOV, Viktor; AUZENAT, François (Elsevier, 2018)Ti6Al4V titanium alloy is widely used in aero-engines due to its superior performance. However, as a difficult-to-cut alloy, it induces short cutting tool life and poor surface integrity. To improve these process outcomes, ...
Optimization-based procedure for the determination of the constitutive model coefficients used in machining simulations Communication avec acteCHENG, Wenyu; OUTEIRO, José; COSTES, Jean-Philippe; M’SAOUBI, Rachid; KARAOUNI, Habib; DIETRICH, Stefan; MARCON, Bertrand; ROSA, Pedro (Elsevier BV, 2019)This paper deals with the determination of the constitutive model coefficients used in machining simulations. An optimization-based procedure is developed and applied to constitutive model coefficients determination of ...
Article dans une revue avec comité de lectureCHENG, Wenyu; OUTEIRO, José; COSTES, Jean-Philippe; M'SAOUBI, Rachid; KARAOUNI, Habib; ASTAKHOV, Viktor (Elsevier, 2019)The predictability of manufacturing process simulation is highly dependent on the accuracy of the constitutive model to describe the mechanical behavior of the work material. The model should consider the most relevant ...
Communication avec acteNASRI, Mohamed Aziz; AGUADO, Jose Vicente; AMMAR, Amine; CUETO, Elias; CHINESTA, Francisco; MOREL, Franck; ROBERT, Camille; EL AREM, Saber (Key Engineering Materials, 2015)Forming processes usually involve irreversible plastic transformations. The calculation in that case becomes cumbersome when large parts and processes are considered. Recently Model Order Reduction techniques opened new ...
Article dans une revue avec comité de lectureCHINESTA, Francisco; LEYGUE, Adrien; BORDEU, Felipe; AGUADO, Jose Vicente; CUETO, Elias; GONZALEZ, David; ALFARO, Iciar; AMMAR, Amine; HUERTA, Antonio (Springer Verlag, 2013)In this paper we are addressing a new paradigm in the field of simulation-based engineering sciences (SBES) to face the challenges posed by current ICT technologies. Despite the impressive progress attained by simulation ...